Question

In: Chemistry

If you were to compare the rates of acylation of ferrocene and acylation of benzene, the...

If you were to compare the rates of acylation of ferrocene and acylation of benzene, the ferrocene would react much faster. What does this tell you about the electron density of the cyclopentadienyl rings on the ferrocene? (The best answers will likely use resonance structures to show how the electron density is distributed in both ferrocene and benzene.)

Solutions

Expert Solution


Related Solutions

If you were to have performed a TLC analysis of ferrocene and acetylferrocenesamples using pure diethyl...
If you were to have performed a TLC analysis of ferrocene and acetylferrocenesamples using pure diethyl ether (rather than as the more polar solvent in a 1:1 mixture with the less polar petroleum ether), which of the two spots would have a greater Rf? Explain briefly.
CHROMATOGRAPHY In running a TLC analysis of ferrocene and acetylferrocene, the two substances were analyzed on...
CHROMATOGRAPHY In running a TLC analysis of ferrocene and acetylferrocene, the two substances were analyzed on a TLC plate in 3 different solvents (1:1 petroleum ether/diethylether, and petroleum ether and diethylether, respectively). What would be some clues that the samples of ferrocene and acetylferrocene being used in this analysis were impure?
1. The possible components of your mixture are unreacted ferrocene and the substituted ferrocene product(s) of...
1. The possible components of your mixture are unreacted ferrocene and the substituted ferrocene product(s) of your reaction, which should travel the farthest up the TLC plate (highest Rf) and why? 2. Which should have a higher Rf value: the mono-substituted ferrocene or the di-substituted ferrocene? 3. In the column chromatography portion of your experiment next week, you use different solvents or solvent mixtures to elute the column for separation of your product mixture. Why is this required? Why use...
Suppose you are a loan office for a bank, and you want to compare interest rates...
Suppose you are a loan office for a bank, and you want to compare interest rates on first mortgages at your branches last month. YOu collect the following data: number 21, 41 mean interest rate 6.60% , 5.90% standard deviation 0.35%, 0.28% . Set up the hypothesis with the proper H0 and H1. Find the F critical value for a=0.05
Rank the polarity of the following compounds: ferrocenecarboxylic acid, acetylferrocene, ferrocenecarboxaldehyde, ferrocene, (dimethylaminomethyl) ferrocene, and ferrocenemethanol...
Rank the polarity of the following compounds: ferrocenecarboxylic acid, acetylferrocene, ferrocenecarboxaldehyde, ferrocene, (dimethylaminomethyl) ferrocene, and ferrocenemethanol and give a detailed explanation why.
You are quantitating benzene using isopropyl-benzene as an internal standard. During the first run, you add...
You are quantitating benzene using isopropyl-benzene as an internal standard. During the first run, you add 100.0 microliters of 500. microgram/mL benzene and 100.0 microliters of 500. microgram/mL isopropylbenzene to a vial and dilute to 1.000mL to prepare a solution that has a final concentration of 50.0 micrograms/mL of benzene and isopropylbenzene. The peak area measured by GC-MS corresponds to 1225 and 1775, respectively. Taking an unknown sample of a solution containing benzene with a volume of 100.0 microliters, you...
Two liquid streams are flowing at constant rates into a blender. One is benzene, which flows...
Two liquid streams are flowing at constant rates into a blender. One is benzene, which flows at a measured rate of 20.0L/min, and the other is toluene. The blended mixture enters a storage tank (inner diameter = 5.5m) equipped with a sight gauge. During an interval in which no liquid leaves the storage tank, the liquid level in the tank is observed to increase by 0.15 meters over a one-hour period. Calculate the flow rate of toluene into the blender...
Melting point of ferrocene = 171.5-172.6 degrees Celcius Literature melting point of ferrocene = 172-174 degrees...
Melting point of ferrocene = 171.5-172.6 degrees Celcius Literature melting point of ferrocene = 172-174 degrees Celcius Melting point of acetylferrocene = 78.9-83.2 degrees Celcius Literature melting point = 81-81 degrees Celcius What do these melting points indicate about the purity and identity of the ferrocene and acetylferrocene samples?
How do Tax Rates in the US compare with tax rates overseas?
How do Tax Rates in the US compare with tax rates overseas?
How do Tax Rates in the US compare with tax rates overseas?
How do Tax Rates in the US compare with tax rates overseas?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT