Question

In: Mechanical Engineering

A gearbox is to be designed with a compound reverted gear train that transmits 25 horsepower...

A gearbox is to be designed with a compound reverted gear train that transmits 25 horsepower

with an input speed of 2500 rev/min. The output should deliver the power at a rotational speed in

the range of 280 to 300 rev/min. Spur gears with 20? pressure angle are to be used. Assuming a diametral pitch of 6 teeth/in. Please show all steps.

(a) Determine pitch diameters for each of the gears.

(b) Determine the pitch line velocities (in ft/min) for each set of gears.

(c) Determine the magnitudes of the tangential, radial, and total forces transmitted between each

set of gears.

(d) Determine the input torque.

(e) Determine the output torque, neglecting frictional losses.

Solutions

Expert Solution


Related Solutions

A compound gear train with gears P, Q, R, S, T and U has number of...
A compound gear train with gears P, Q, R, S, T and U has number of teeth 10, 20, 02 40, 50, 80 and 100 respectively. Show the arrangement of gears for a speed reduction of 50% and determine the center distance between driving and driven shafts if the diametrical pitch of the gears is 0.5 I only have this question , cant give you more information
countershaft in Prob. 3–72, p. 152, is part of a speed reducing compound gear train using...
countershaft in Prob. 3–72, p. 152, is part of a speed reducing compound gear train using 20° spur gears. A gear on the input shaft drives gear A. Gear B drives a gear on the output shaft. The input shaft runs at 2400 rev/min. Each gear reduces the speed (and thus increases the torque) by a 2 to 1 ratio. All gears are to be of the same material. Since gear B is the smallest gear, transmitting the largest load,...
This is for a VF-30 Bonfiglioli worm drive Gearbox 6.1 Housing 6.2 Worm Gear 6.3 Worm...
This is for a VF-30 Bonfiglioli worm drive Gearbox 6.1 Housing 6.2 Worm Gear 6.3 Worm Shaft For each of the MAJOR components (6.1, 6.2 and 6.3) stated only, analyze and identify the manufacturing processes used to make the component – both primary (bulk shape forming) and secondary (or finishing) processes. Include sub-sub-section as follows for each component: o 6.1.1 Component Observations: Describe your observations of the physical component which indicate what manufacturing processes were performed. Include an annotated picture...
A power train application requires the coupling of a spur gear to a transmission shaft operating...
A power train application requires the coupling of a spur gear to a transmission shaft operating at 3600RPM. The coupling must sustain a mean torque loading of 215Nm. There is a 20% torque ripple introduced to the drive line from the load. Select and design a coupling system using either a keyed coupling or an interference coupling such that the section of the transmission shaft at that location is minimized. Assume that the gear is located at the midpoint of...
In the planetary gear train shown in Figure Q2, the annulus A rotates at 300 rpm...
In the planetary gear train shown in Figure Q2, the annulus A rotates at 300 rpm about the axis of fixed wheel S which has 80 teeth. The armed spider (arm) is driven at 180 rpm. The annulus is connected to input shaft whereas the arm is connected to the output shaft. If the efficiency of gear system is 98% and input torque is 100 Nm, identify the following information regarding these problems (i) The number of teeth on planet...
Design a speed-increasing gear train with a speed ratio of SPR defined below: Speed ration =...
Design a speed-increasing gear train with a speed ratio of SPR defined below: Speed ration = 13 The gear train does not need to be reverted. Specify the appropriate numbers of teeth to minimize the gearbox size while avoiding the interference problem in the teeth. Perform the analysis subject to the following constraints: A) Use a 20° pressure angle and match SPR exactly. B) Use a 25° pressure angle and match SPR exactly. C) Use a 20° pressure angle and...
Explain briefly the differences between simple, compound, and epicyclic gear trains
Explain briefly the differences between simple, compound, and epicyclic gear trains
Ooba Electronics is considering whether to develop a new line of robots designed to train dogs....
Ooba Electronics is considering whether to develop a new line of robots designed to train dogs. The first generation robots will be on the market for 3 years, after which Ooba could release an improved second-generation dog-training robot. Data for the both the first-generation and second-generation projects are summarized below. 1st Generation: Robots are expected to sell for $600 in years 1 through 3. Sales volume is expected to be 3000, 6000 and 10000 in years 1 to 3 respectively....
Ooba Electronics is considering whether to develop a new line of robots designed to train dogs....
Ooba Electronics is considering whether to develop a new line of robots designed to train dogs. The first generation robots will be on the market for 3 years, after which Ooba could release an improved second-generation dog-training robot. Data for the both the first-generation and second-generation projects are summarized below. 1st Generation: Robots are expected to sell for $600 in years 1 through 3. Sales volume is expected to be 3000, 6000 and 10000 in years 1 to 3 respectively....
A pair of gears with 25?, full-depth, involute teeth transmits 125 hp while the pinion rotates...
A pair of gears with 25?, full-depth, involute teeth transmits 125 hp while the pinion rotates at 2500 rpm. The diametral pitch is 4, and the quality number is A9. The pinion has 32 teeth and the gear has 76 teeth. The face width is 1.5 in. The input power is from a multicylinder gasoline engine, and the drive is for a low speed water pump. The drive is a commercial enclosed gear unit. Specify suitable materials for the pinion...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT