Question

In: Mechanical Engineering

Subject: Heat exchanger Lab Question: 1.1) in heat exchanger analysis, the following quantities are used. Explain...

Subject: Heat exchanger Lab

Question:

1.1) in heat exchanger analysis, the following quantities are used. Explain what each means and give
a formula for each. Assume the mass flow rates, fluid properties, inlet, temperatures, and length
and diameters of the heat exchanger are known.

a) Overall heat transfer coefficient. UA.

b) A number of transfer units, NTU.

c) Effectiveness, e

1.2) what is the hydraulic diameter and why is it useful for double-pipe heat exchanger analysis?

Solutions

Expert Solution


Related Solutions

List two methods that are used in heat exchanger design and analysis.
List two methods that are used in heat exchanger design and analysis.
In a thermofluids lab, a student is analysing a prototype single-pass cross-flow heat exchanger used to...
In a thermofluids lab, a student is analysing a prototype single-pass cross-flow heat exchanger used to cool water from 90oC to 60oC by transferring its heat to an air stream with an inlet temperature of 30oC without mixing. The water and air flow rates are 42,000 kg/h and 180,000 kg/h respectively. Assume that for the water cp=4.18kJ/kg⋅oC and for the air cp=1.02kJ/kg⋅oC. Calculate the log mean temperature difference for this heat exchanger.
A heat exchanger is used to transfer heat from a steam stream to a chlorine gas...
A heat exchanger is used to transfer heat from a steam stream to a chlorine gas stream. 100 kg of steam at 1 bar and 250°C enters the heat exchanger and leaves the exchanger as saturated steam at 1 bar. Chlorine gas enters the exchanger at 1 bar and 33.0°C and leaves the exchanger at 132.0°C. Assume the heat exchanger is adiabatic. A)What is the specific enthalpy of the inlet steam stream? (Use liquid water at 0.01°C as a reference...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30...
A shell-and-tube heat exchanger is to used to heat water (in the tube side) from 30 deg C to 40 deg C at a mass flow rate of 4 kg/s. The fluid used for heating (shell side) is water entering at 90 deg C with a mass flow rate of 2 kg/s. A 1-2 STHE is used and the overall heat transfer coefficient based on the inside area is 1390 W/m2-K. The tubes are 1.875 in diameter (inside) and require...
A heat exchanger is used to heat acetone. 10 kg/min of steam enters at 550 C...
A heat exchanger is used to heat acetone. 10 kg/min of steam enters at 550 C and 20.0 bar and leaves as saturated steam at 1 bar. The acetone enters at 20 C and leaves at 70 C. The heat exchanger loses 3000 kJ/min to the surroundings. The acetone is under a constant pressure of 1 atm. Determine the volumetric flow rate (L/h) of acetone leaving the heat exchanger.
Saturdated water vapor (steam) is commonly used as a heat source in heat exchanger applications. Why...
Saturdated water vapor (steam) is commonly used as a heat source in heat exchanger applications. Why saturated vapor? Why saturated water vapor? In a plant of any reasonable size, several varieties of saturated steam are commonly available; for example, saturated steam at 4.5,9,17, and 33 bar. But the higher the pressure the lower the useful energy content (why?), and the greater the unit cost. Why then is higher-pressure steam used?
In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy...
In a pipe heat exchanger, crude oil on 30 ℃ is used to cool the heavy oil from 180℃ to 120℃.Mass flow of heavy oil is Wh=104kg / h,and crude oil respectively Wc=1.3×104kg/h. Specific heat, respectively is Cph=2.2 kJ/(kg•℃), Cpc=1.9 kJ/(kg•℃). Overall heat transfer coefficient K=120W/(m2•K). Try to calculate the required heat transfer area for parallel flow and countercurrent flow.
Heat transfer In a test in a double tube heat exchanger the following data are obtained...
Heat transfer In a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...
Heat transfer in a test in a double tube heat exchanger the following data are obtained...
Heat transfer in a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...
A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large...
A counterflow, concentric tube heat exchanger is used to cool the lubricating oil for a large industrial gas turbine engine. The flow rate of cooling water through the inner tube (Di = 25 mm) is 0.2 kg/s, while the flow rate of oil through the outer annulus (Do = 45 mm) is 0.1 kg/s. The oil and water enter at temperatures of 100 and 30 C, respectively. How long must the tube be made if the outlet temperature of the...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT