Question

In: Mechanical Engineering

What is the therotiacal And The expertmatla heat transfer cofficnent for heat exchanger in my case...

What is the therotiacal And The expertmatla heat transfer cofficnent for heat exchanger in my case shell and tube

Therotical ?

formual ??

expermantial ?

formula ?

I am uisng LMTD method

Solutions

Expert Solution

For Tube side heat transfer coefficient ,we can use correlation as usual based on Reynolds Number.

There is data available about the range of heat transfer coefficients based on experiments


Related Solutions

HEAT TRANSFER: HEAT EXCHANGER Oil flows in a heat exchanger with a mass flow rate of...
HEAT TRANSFER: HEAT EXCHANGER Oil flows in a heat exchanger with a mass flow rate of 20 kg/s and is to be cooled from 175 to 65°C with water as a coolant flowing at a rate of 30 kg/s and an inlet temperature of 12°C. The overall heat transfer coefficient is U = 1250 W/m2⋅K. a) Sketch the temperature profile and calculate the mean temperature for parallel flow, counter flow, and cross flow heat exchangers.. b) Determine the area required...
Heat transfer question A shell-and-tube heat exchanger is used to heat a liquid that flows in...
Heat transfer question A shell-and-tube heat exchanger is used to heat a liquid that flows in tubes of inside and outside diameters Di=10 mm and Do=11 mm. You have been asked to choose the most cost-efficient material for the tubes. Material A has a density ρA=8900 kg/m3 and a thermal conductivity kA= 10 W/m·K. Material B has a density ρB=1780 kg/m3 and a thermal conductivity kB=0.17 W/m·K. The cost of material A per unit mass is three times the cost...
Heat transfer In a test in a double tube heat exchanger the following data are obtained...
Heat transfer In a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...
A heat exchanger is used to transfer heat from a steam stream to a chlorine gas...
A heat exchanger is used to transfer heat from a steam stream to a chlorine gas stream. 100 kg of steam at 1 bar and 250°C enters the heat exchanger and leaves the exchanger as saturated steam at 1 bar. Chlorine gas enters the exchanger at 1 bar and 33.0°C and leaves the exchanger at 132.0°C. Assume the heat exchanger is adiabatic. A)What is the specific enthalpy of the inlet steam stream? (Use liquid water at 0.01°C as a reference...
Heat transfer in a test in a double tube heat exchanger the following data are obtained...
Heat transfer in a test in a double tube heat exchanger the following data are obtained For hot fluid Flow = 11.6 gal / sec Outlet temperature = 30.1 ° C Inlet temperature = 32 ° C For cold fluid Flow 11gal / min Outlet temperature 25.1 ° C Inlet temperature 24.2 ° C For the fluid consider k = 0.49 w / mK cp = 3729.95 J / kgK Prandtl number = 14.29 Density = 1035.02kg / m3 Get:...
Address the following questions related to heat exchanger effectiveness. Recall that the maximum heat transfer possible...
Address the following questions related to heat exchanger effectiveness. Recall that the maximum heat transfer possible is the product of the minimum heat capacity (mass flow rate times specific heat) times the difference between the hot and cold side inlet temperatures. a. sketch the temperature profiles for a 50% and 80% effectiveness heat exchanger. make sure you have the correct shape which includes the degree of steepness at each end. b. What is the effectiveness for a heat exchanger with...
HEAT TRANSFER QUESTION A shell-and-tube heat exchanger with one shell pass and four tube passes, that...
HEAT TRANSFER QUESTION A shell-and-tube heat exchanger with one shell pass and four tube passes, that contains 190 pipes (thin walled, 4m long, 2.6 cm diameter), will be used to heat the air. Water enters the pipes at 350 K with 8kg/s mass flow rate while the air enters the shell at 15 C with 18kg/s mass flow rate. In time there will be a fouling factor of 0.0026m2K/W on the inside of pipes. Inside heat transfer coefficient is 450...
Determine the overall heat transfer coefficient (U) in a heat exchanger that uses steam to heat water to the point of vaporization (in vacuum.)
Determine the overall heat transfer coefficient (U) in a heat exchanger that uses steam to heat water to the point of vaporization (in vacuum.) The system is non-insulated, so the heat lost to the surroundings must be taken into consideration. While I know that the heat Q = mCdT and the heat transfer rate q = UAdT(Log-mean), I am struggling to equate the two due to the heat lost to the surroundings. How do I go about determining the overall...
What is called Supertargetting in Heat Exchanger Network Design? How Heat Exchanger Network Design can be...
What is called Supertargetting in Heat Exchanger Network Design? How Heat Exchanger Network Design can be done by paying attention to Supertargetting?
Explain heat transfer, latent heat and change in temperature for the following case: Ice kept at...
Explain heat transfer, latent heat and change in temperature for the following case: Ice kept at -10 degrees C temperature turns into water at +10 degrees C temperature upon heating.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT