Question

In: Electrical Engineering

We have a controller, and every time the Operator changes the Set Point, the controller responds,...

We have a controller, and every time the Operator changes the Set Point, the controller responds, and gets the process sorted out. Now, somewhere, we have read that load disturbances needed to be considered in processes, as well. How will this controller react, if there is a load disturbance, and not a Set Point change? provide a basic answer to this.

Solutions

Expert Solution

The universe of single input single output control loops can be separated into two classifications; self-regulating and non self-regulating.

Self Regulating

  • These loops are to such an extent that if the controller is put in manual, the procedure variable will go to some steady state, accepting the collaborating factors are held constant.
  • Examples - flow, heat exchanger temperature control, and even pH.
  • This is the means by which self regulating process behaves. If while the controller is in manual and the process is stable, if the output is change, the process variable or signal will also change, but it will come to a stable point. If the output is moved again, the process variable will come to a different point. The system is stable at an infinite number of points.

Non Self regulating

  • These loops behave such that if the controller is placed in manual, the process variable will go to some saturated state.
  • Examples of these are gas pressure and tank level with a constant input or output.
  • Envision a gas volume with a settled hole in the outlet, to a "steady" backpressure. Expect that a control valve drops a gas weight to this tank from a considerably higher pressure.
  • If the loop is placed in manual and the valve moved to some point, the pressure, in time, will either build to a point almost equal to the supply pressure or drop to a point almost equal to the back pressure.
  • The system is stable at only one point.
  • Non self-regulating loops have "built in reset action and therefore can be tuned without reset.
  • Sometimes, depending on the controller's method of gain, you may experience some offset, but offsetting the set point or adding bias can compensate for this.
  • One can see the differences in these loops by experiments done at home.

Related Solutions

Q1. We have a controller, and every time the Operator changes the Set Point, the controller...
Q1. We have a controller, and every time the Operator changes the Set Point, the controller responds, and gets the process sorted out. Now, somewhere, we have read that load disturbances needed to be considered in processes, as well. How will this controller react, if there is a load disturbance, and not a Set Point change?                                                                                                                        Q3. The Process Variable jumps around, quite a bit. Which of the PID settings should we not be using, to improve controllability, and...
We have an array of numbers, and we start at index 0. At every point, we're...
We have an array of numbers, and we start at index 0. At every point, we're allowed to jump from index i to i+3, i+4, or stop where we are. We'd like to find the maximum possible sum of the numbers we visit. For example, for the array [14, 28, 79, -87, 29, 34, -7, 65, -11, 91, 32, 27, -5], the answer is 140. (starting at the 14, we jump 4 spots to 29, then 3 spots to 65,...
We would like to have a simple model to describe how temperature changes with time in...
We would like to have a simple model to describe how temperature changes with time in your classroom during lecture in a typical day in Fall and Spring. You can consider two sets of average air temperature – one in October and other one in April for your analysis. Also, for simplicity, consider the entire room to be at one temperature T. Outside air (Ti,) comes in and reaches the temperature of the room through mixing, and this air leaves...
A production company has observed that there are changes in revenue every time it tries to...
A production company has observed that there are changes in revenue every time it tries to manipulate the price. The concerns of management were brought to your attention needing your expertise advice on how price influences quantity and subsequently revenue. The market survey revealed that the quantity demanded of the product follows a Cobb-Douglas function as presented below: Q"dx"= αP"x^β"+ε^u ........... of the form Q=AL^αK^β (Cobb Douglas production fuction) Where Qdx is the quantity demanded of commodity X and Px...
Often a firm will calculate the break-even point for a price. That is, if we set...
Often a firm will calculate the break-even point for a price. That is, if we set the price at $X, then how many units will we need to sell to cover costs (that is, our break-even point). Work through the following data and questions to gain a better understanding of this approach. QUESTIONS Start by completing the above table under the assumption that the product will be sold for $30. (It will be easiest to use Excel to complete the...
Analysis Essay The evolution of technology is changing every day with those changes we find the...
Analysis Essay The evolution of technology is changing every day with those changes we find the version of norm adapts. Radios, computers, cell phones, and even household items have taken a technological route to make a human's life easier. The technology was created to make life easier, using these machines increases productivity. The changes in technology will have society always adapting to the new world, generations before and after will also continue to adapt to the advancement of these changes....
Is it necessary for every research project to have a set of hypotheses? Why or why...
Is it necessary for every research project to have a set of hypotheses? Why or why not? What is the role of the researcher in the problem definition process? How may a marketing researcher be creative in interpreting a research brief and developing a research proposal? What is the significance of the ‘background’ section of a research brief and research proposal? Describe some of the reasons why management is often not clear about the ‘real’ problem they face. What interrelated...
Suppose workers are not very sensitive to unemployment. The result will be that inflation will jump a lot every time inflation changes.
TRUE OR FALSEa) Suppose workers are not very sensitive to unemployment. The result will be that inflation will jump a lot every time inflation changes.b) If in short-run equilibrium inflation is greater than expected inflation, then it must be true that output is less than potential output.c) The economy may be away from its medium-run equilibrium for a while because actual inflation rates take a while to adjust.d)Suppose the economy starts from the (potential output, expected inflation) point. A leftward...
In Nonlinear regression analysis, if we have a data set and if we need to model...
In Nonlinear regression analysis, if we have a data set and if we need to model nonlinear, once we enter the data either in R or SPSS software we observe the results, but we cannot see the exact equation as we can write for linear regression.as an example if we want to see the relationship between Sales the response variable and the advertising budget for TV media and News paper we have to independent variables,once the data we entered how...
We have been using the same set of data (Data Set One) in the notes to...
We have been using the same set of data (Data Set One) in the notes to illustrate production and costs. I have provided Data Set One in both tables below. When costs were calculated in the notes, fixed costs were $200. By using the term fixed costs economists are only referring to the fact that a firm must pay this expense no matter how much output it produces or sells. An example of a fixed cost could be the rent...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT