Question

In: Civil Engineering

A 3 m by 3 m square footing is sitting 1.6 m below the ground surface....

A 3 m by 3 m square footing is sitting 1.6 m below the ground surface. The anticipated column loads include a moment (M=50 kN.m), a horizontal force (Qh=40kN, acting in the same direction as the moment) at the ground surface and a vertical force (Qv=260kN). Determine the minimum and maximum stress beneath the footing and draw the stress profile diagram to scale.

Solutions

Expert Solution


Related Solutions

A strip wall footing 1.5 m wide is located 1.1 m below the ground surface. Supporting...
A strip wall footing 1.5 m wide is located 1.1 m below the ground surface. Supporting soil has a unit weight of 19.60 kN/m3 . The results of laboratory tests on the soil samples indicated that the supporting soil has the following properties: c’ = 57.5 kN/m2 and I’ = 25°Groundwater surface was not encountered during the subsurface exploration. Determine the allowable bearing capacity of the soil using a factor of safety of 2.5.
A strip footing 2.5 m wide is loaded on the ground surface with a pressure equal...
A strip footing 2.5 m wide is loaded on the ground surface with a pressure equal to 175 kPa. Calculate the stress distribution at depths of 2.5, 7.5 and 12.5 m under the center of the footing. If the footing rested on a normally consolidated cohesive layer whose Cc was 0.612 and whose e0 was 1.35 , estimate the settlement of the footing. Assume S = 100%,γ’ = 7.5 kN/m3 , and the total clay layer thickness beneath the footing...
Determine the size of a square footing at the ground level to transmit a load of...
Determine the size of a square footing at the ground level to transmit a load of 900 kN in sand weighing 18 kN/m3 and having an angle of shearing resistance of 36° (Nγ = 46, Nq = 43). Factor of safety is 3. What will be the modification in the result, if the footing may be placed at a depth of 1 m below ground surface ? Assume, in this case, the water table may rise to the ground surface....
A 2.8 m wide reinforced concrete strip footing is situated at 2.5 m below ground level...
A 2.8 m wide reinforced concrete strip footing is situated at 2.5 m below ground level in a thick deposit of a saturated clay. The footing is loaded centrally, and the total vertical line load including the weight of the concrete and backfill is 308 kN/m. The clay has a bulk density (ρ) of 2250 kg/m3 and an undrained shear strength (cu) of 42 kPa. a) Calculate the factor of safety against bearing capacity failure considering the short term response...
A square footing 4 m × 4 m is located at a depth of 1.0 m...
A square footing 4 m × 4 m is located at a depth of 1.0 m in a layer of saturated clay 13 m thick, a firm stratum lies immediately below the clay. Characteristic parameters obtained from oedometer and triaxial tests for the clay are as follows: A= 0.42, cu =100 kPa, , u  0 c' 0, ' 32, 0.065 / , 2 mv  m MN 3  sat  21kN / m , Eu = 300cu. Determine...
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing?
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing? please show each steps with how you solved to obtain value of B
500 mm thick square footing is to be placed at a depth of 0.5 m in...
500 mm thick square footing is to be placed at a depth of 0.5 m in a clayey sand where c¢ = 10 kPa, f¢ = 34°, g = 19.0 kN/m3. The column load to be applied on the footing is 2000 kN. What should be the width of the footing?
A portable radio is sitting at the edge of a balcony 5.1 m above the ground....
A portable radio is sitting at the edge of a balcony 5.1 m above the ground. The unit is emitting sound uniformly in all directions. By accident, it falls from rest off the balcony and continues to play on the way down. A gardener is working in a flower bed directly below the falling unit. From the instant the unit begins to fall, how much time is required for the sound intensity level heard by the gardener to increase by...
A tractor is pulling a drawbar tillage implement at a ground speed of 1.6 m/s. The...
A tractor is pulling a drawbar tillage implement at a ground speed of 1.6 m/s. The total rear axle static load is 35 kN, the wheelslip is 0.1, and the value of mobility number for the particular tyre and soil is 2.84. The driving tyre radius is 0.6 m, and the engine speed is 2100 rpm, and the overall gear transmission mechanical efficiency is 79%. Calculate the drawbar pull, drawbar power and the tractive efficiency Calculate the wheel axle power...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT