Question
In: Mechanical Engineering
If the weight of the contents in a vessel is measured and the density of the...
If the weight of the contents in a vessel is measured and the density of the material is known, fill in the blanks to describe what steps are required to determine level. Find the ____________________ by dividing weight by ____________________, and then find the ____________________ by dividing ____________________ by the ____________________ of the vessel.
Fill in the blanks?
Solutions
Expert Solution
Find the volume of material displaced by dividing weight by specific weight of material, and then find the level by dividing volume displaced by the cross section area of the vessel.
Let w=weight placed
D=density of materials
g=acceleration of gravity
then S= specific weight = D*g
A= cross section area of vessel
If any amendments are needed, then let me know in comments.
samet mamat answered 2 years agoRelated Solutions
The amount of fill (weight of contents) put into a glass jar of spaghetti sauce is...
The amount of fill (weight of contents) put into a glass jar of
spaghetti sauce is normally distributed with mean μ = 843
grams and standard deviation of σ = 8 grams.
(a) Describe the distribution of x, the amount of fill
per jar.
1) skewed right
2) normal
3) skewed left
4) chi-square
_
(b) Find the probability that one jar selected at random contains
between 835 and 865 grams. (Give your answer correct to four
decimal places.)
_...
The amount of fill (weight of contents) put into a glass jar of spaghetti sauce is...
The amount of fill (weight of contents) put into a glass jar of
spaghetti sauce is normally distributed with mean μ = 859
grams and standard deviation of σ = 15 grams.
b) Find the probability that one jar selected at random contains
between 841 and 860 grams. (Give your answer correct to four
decimal places.)
(d) Find the mean of the x distribution. (Give your answer
correct to the nearest whole number.)
(ii) Find the standard error of the...
The amount of fill (weight of contents) put into a glass jar of spaghetti sauce is...
The amount of fill (weight of contents) put into a glass jar of
spaghetti sauce is normally distributed with mean
μ
= 840
grams and standard deviation of
σ
= 9
grams.
(a) Describe the distribution of
x, the amount of fill per jar.
skewed right
normal
skewed left
chi-square
(b) Find the probability that one jar selected at random contains
between 843 and 858 grams. (Give your answer correct to four
decimal places.)
(c) Describe the distribution of x,...
A cylindrical beaker of height 0.100 m and negligible weight is filled to the brim with a fluid of density ρ = 890 kg/m3 . When the beaker is placed on a scale, its weight is measured to be 1.00 N
A cylindrical beaker of height 0.100 m and negligible weight is filled to the brim with a fluid of density ρ = 890 kg/m3 . When the beaker is placed on a scale, its weight is measured to be 1.00 N .(Figure 1)
A ball of density ρb = 5000 kg/m3 and volume V = 60.0 cm3 is then submerged in the fluid so that some of the fluid spills over the side of the beaker. The ball is held...
In a study where the capability of a gauge was measured by the weight of paper,...
In a study where the capability of a gauge was measured by the
weight of paper, the following measurements were obtained: 3.481
3.448 3.485 3.475 3.472 3.477 3.472 3.464 3.508 3.170 4.123 3.470
2.893 3.473 4.201 3.474 4.301 3.021 3.231 3.405
Part I Using R do the following: 1. Draw an appropriately titled
histogram. Interpret the graph. 2. Draw an appropriately titled
boxplot. Interpret the graph. 3. Compute the five-number summary.
4. Find the interquartile range. 5. Find the mean...
In a study where the capability of a gauge was measured by the weight of paper,...
In a study where the capability of a gauge was measured by the
weight of paper, the following measurements were obtained: 3.481
3.448 3.485 3.475 3.472 3.477 3.472 3.464 3.508 3.170 4.123 3.470
2.893 3.473 4.201 3.474 4.301 3.021 3.231 3.405
Part I Using R do the following(SHOW R CODE): 1. Draw an
appropriately titled histogram. Interpret the graph. 2. Draw an
appropriately titled boxplot. Interpret the graph. 3. Compute the
five-number summary. 4. Find the interquartile range. 5. Find...
A rough analysis of cell contents suggests their cytoplasm contains 5% by weight of solutes: 1%...
A rough analysis of cell contents suggests their cytoplasm
contains 5% by weight of solutes: 1% is proteins of average
molecular weight 45,000; 1% is soluble lipids of molecular weight
400; 1% is sugars of molecular weight 170; and 2% is salts like
KCl. What is the osmotic pressure inside these cells relative to
pure water at 37C? Assume the density of the cytoplasm is
approximately 1g/cm^3 and has the properties of water.
An alloy is composed of elements A (78%) and B (12%) by weight. The density of...
An alloy is composed of elements A (78%) and B (12%) by weight.
The density of the alloy is 1.95 g/cm3. The properties
of these elements are shown below:
Element
Gram Atomic Weight
σa (barns)
σs (barns)
A
22.1999
0.19
1.38
B
25.0055
0.21
2.44
Determine:
The atom densities for the two elements.
The atomic density for element A:
b. The absorption and scattering macroscopic cross sections for
thermal neutrons.
c. The mean free paths for absorption and...
The weight of a metal bracelet is measured to be 0.12200 N in air and 0.07800...
The weight of a metal bracelet is measured to be 0.12200 N in
air and 0.07800 N when immersed in water. Find its density.
Question Background information: - The molecular weight of ethanol (C2H5OH) is 46.1 and the density of...
Question
Background information:
- The molecular weight of ethanol (C2H5OH) is 46.1 and the
density of absolute (100%) ethanol = 0.79 g/mL.
- Assume that a 80 kg person contains 48 L of ‘water’. Ignore
the metabolism, and assume the water content of the person remains
constant.
- The legal limit for a driver’s blood alcohol in Australia is
50 mg of ethanol per 100 mL of blood (referred to as a blood
alcohol content (BAC) of 0.05%).
a.) During...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Describe System Development Life Cycle (SDLC) and how it is used.
- What symbolism do you find in the play,Oedipus?
- • Using the Scanner class to obtain input from the user. • Using printf to output...
- In each of the following situations, develop a tentative plan for the client. List the various...
- MARGI sells different types of wine. Customers place orders to the most popular “Summer Wine” at...
- Java. If possible please put explanations for each line of code. Write a test program that...
- . Use the following information to calculate your company's expected return State Probability Return Boom 20%...
ADVERTISEMENT