A steam power plant operates with a maximum pressure of 3500 psia and maximum temperature of...

A steam power plant operates with a maximum pressure of 3500 psia and maximum temperature of 1050 ^oF. Assume a simple Rankine cycle, condenser pressure is 10 psia, and turbomachinery is isentropic.

Turbine work in Btu/lb

Pump work in Btu/lb

Heat addition in steam generator in Btu/lb

Cycle thermal efficiency

Expert Solution

samet mamat answered 2 years ago

Steam enters the high-pressure turbine of a steam power plant that operates on the ideal reheat...

Steam enters the high-pressure turbine of a steam power plant that operates on the ideal reheat Rankine cycle at 6 MPa and 500°C and leaves as saturated vapor. Steam is then reheated to 400°C before it expands to a pressure of 10 kPa. Heat is transferred to the steam in the boiler at a rate of 6*104 kW. Steam is cooled in the condenser by the cooling water from a nearby river, which enters the condenser at 7°C. Show the...

A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine...

A steam turbine operates adiabatically at a power level of 3500 kW. Steam enters the turbine at 2400 kPa and 500oC and exhausts from the turbine at 20 kPa as saturated vapor. What is the flow rate of steam run through the turbine, and what is the turbine efficiency? Draw the process on the P-H diagram.

A steam Rankine cycle operates between the pressure limits of 1500 psia in the boiler and...

A steam Rankine cycle operates between the pressure limits of 1500 psia in the boiler and 1 psia in the condenser. The turbine inlet temperature is 800°F. The turbine isentropic efficiency is 90 percent, the pump losses are negligible, and the cycle is sized to produce 2500 kW of power. Calculate the mass flow rate through the boiler, the power produced by the turbine, the rate of heat supply in the boiler, and the thermal efficiency. Use steam tables

A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at...

A steam power plant operates on a practical Rankine Cycle. The steam enters the turbine at 3 MPa and “648” K and is condensed in the condenser at a pressure of 46 kPa. You are assigned on a project to improve the thermal efficiency of this plant. a) Draw the schematic of the plant and determine the thermal efficiency of the practical cycle assuming that the efficiencies of pump and turbine are 0.75 and 0.7, respectively. ( b) Draw a...

A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine...

A steam power plant operates on the simple ideal rankine cycle. the steam enters the turbine at 4 MPa and 500 C and leaves it at 50 kPa and 150 C. the water leaves the condenser as a saturated liquid and is subsequently displaced to the boiler by means of a pump at a temperature of 85 C, which is the isentrophic efficiency of the turbine?

A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6...

A steam power plant operates on a regenerative Rankine cycle. Steam enters the turbine at 6 MPa at 700 ºC and the condenser at 10 kPa. Turbine has isentropic efficiency of 85% and pumps have isentropic efficiency of 90%. Steam is extracted from the turbine at 0.6 MPa to heat the feedwater in an open feedwater heater. Water leaves the open feedwater heater as saturated liquid. a) Draw the system with labels and show the ideal and the non-ideal cycle...

4. A Rankine cylce operates between pressures of 2 psia and 1500 psia. If the steam...

4. A Rankine cylce operates between pressures of 2 psia and 1500 psia. If the steam entering the turbine is superheated to 800oF, calculate the efficiency of the cycle. Neglect pump work. Note: The peak of the superheat phase of this cycle is outside the range of the text steam tables and is difficult to locate on the text Mollier chart since it does not have a 1500 psia constant pressure line. Please use the following information taken from the...

A steam turbine operates with steam at inlet conditions of 3.5 MPa and 3500 C. The...

A steam turbine operates with steam at inlet conditions of 3.5 MPa and 3500 C. The exit stream leave the turbine is at 0.8 MPa and is known to contain a mixture of saturated vapor and liquid. The steam rate through the turbine is 1000 kg/h. A (negligible) fraction of exit stream is bled through a throttle valve to 0.10 MPa and is found to be 1250 C. The measured output of the turbine is 100 kW. a) Determine the...

A steam power plant operates with a boiler that is heated from a heat source at...

A steam power plant operates with a boiler that is heated from a heat source at 457 °C and produces 450 ton/hr. of steam. The steam leaves the boiler at 425 °C and 4 MPa. The steam reaches a turbine at 375 °C and 3 MPa and leaves it at 50 kPa with 4% liquid water. This mixture is flown into a condenser that rejects the heat into a river at 17 °C. Water leaves the condenser at 50 kPa...

a steam power plant operates on a superheated rankine cycle where steam at 10kg/s entering the...

a steam power plant operates on a superheated rankine cycle where steam at 10kg/s entering the turbine at 5MPa and 375 degree celcius and leaving the turbine at saturated vapor at pressure 100 times less then initial. If the compressor efficiency is 85% , I) sketch the cycle of T-s diagram ii) calculate the temperature and pressure for all points in the cycle iii) calculate the compressor work iv) calculate the turbine work and turbine efficiency v.) calculate the thermal...

Question