Question

In: Chemistry

Chemical Engineering. The product gas from a coal gasification plant consists of 60.0 mole % CO...

Chemical Engineering. The product gas from a coal gasification plant consists of 60.0 mole % CO and the balance H2; it leaves the plant at 150° C and 2000 psia. The gas expands through a turbine, and the outlet gas from the turbine is fed to a boiler furnace at 100° C and 1atm at a rate of 15,000 ft^3/min. Estimate the inlet flow rate to the turbine in ft^3/min using Kay's rule. What percentage error would result from the use of the ideal gas equation of state at the turbine inlet?
Please show work.

Solutions

Expert Solution


Related Solutions

Natural gas consists of 60.0 mole% ethane and 40.0 mole% butane. The gas is stored in...
Natural gas consists of 60.0 mole% ethane and 40.0 mole% butane. The gas is stored in a 300 ft^3 tank at a pressure of 1500 psig, and a temperature of 220 F and sold at a cost of $0.15/lb. a) Determine whether the ideal gas equation of state is a good approximation for the given conditions. b) Estimate the cost to fill the tank using the compressibility-factor equation of state.
Chemical Engineering Problem: A vapor composed of 0.25 mole fraction ethanol and 0.75 mole fraction acetic...
Chemical Engineering Problem: A vapor composed of 0.25 mole fraction ethanol and 0.75 mole fraction acetic acid at 120.0 mmHg (absolute), is in equilibrium with a liquid phase also composed of ethanol and acetic acid. Assume that the liquid is an ideal solution and apply Raoult\'s law to find the following. What is the temperature of the liquid? What is the Temperature of the fluid? _____C What are the mole fractions of the liquid phase? XE=_____mol ethanol/mol XA=_____mol acetic acid/mol
Chemical engineering question A synthesis gas containing 6.4% CO2, 0.2% O2, 40.0% CO and 50.8% H2...
Chemical engineering question A synthesis gas containing 6.4% CO2, 0.2% O2, 40.0% CO and 50.8% H2 (the remainder is N2) is burned with 40 % excess dry air (assume 21 % O2 and 79 % N2). i)Identify the reactions occurring during combustion of this syngas. ii)Calculate the amount of air added per 100 mol of syngas. iii)If complete combustion occurs, then calculate the composition of the flue gas on a weight basis.
You are working on a feedwater system for a chemical engineering plant. A section of the...
You are working on a feedwater system for a chemical engineering plant. A section of the pipe passes through a stream of width ? = 4 m which flows at constant temperature and velocity (?∞ = 12 °C,?∞ = 1.7 m⁄s). You need to determine the temperature change of the feedwater as it passes through the stream. The feedwater is 20 °C as it enters the section passing through the stream. The pipe diameter is 4 inches and the volume...
(Chemical Engineering) Why would any gas at STP be considered ideal?
(Chemical Engineering) Why would any gas at STP be considered ideal?
11. A synthetic gas generated from coal has the following composition CO2- 7.2%; CO- 24.3%; H2-...
11. A synthetic gas generated from coal has the following composition CO2- 7.2%; CO- 24.3%; H2- 14.1%; CH4- 3.5%; N2- 50.9%. a. Calculate the cubic feet of air required for complete combustion per cubic foot of synthesis gas under the same conditions. b. If 38% of excess air is used for combustion, what volume of combustion gas at 750 F and 738 mm Hg would be produced per cubic foot of synthetic gas under standard conditions?
A gas turbine plant consists of a compressor with a pressure ratio of 10, a combustion...
A gas turbine plant consists of a compressor with a pressure ratio of 10, a combustion chamber, and a turbine mounted on the same shaft as the compressor; the net electrical power of the unit is 20 MW. The inlet air conditions are 1.013 bar and 15 ?C and the maximum cycle temperature is 1100 K. The exhaust gases from the turbine are passed through a heat exchanger to heat water for space heating before passing to the chimney; by...
Moles of Reactant to Moles of Product: Use mole ratio from balanced chemical equation. 1.Ammonia burns...
Moles of Reactant to Moles of Product: Use mole ratio from balanced chemical equation. 1.Ammonia burns in oxygen according to the following equation: 4 NH3 + 3 O2  → 2 N2 + 6 H2O How many moles of nitrogen gas are generated by the complete reaction of 8.23 moles of ammonia? Express your answer to two decimal places. mol N2 2. Moles of Product to Moles of Reactant: Use mole ratio from balanced chemical equation. The commercial process used to make...
A 30.0-liter cylinder of gas containing 97.0 mole % CO and 3.0% CO2 is delivered to...
A 30.0-liter cylinder of gas containing 97.0 mole % CO and 3.0% CO2 is delivered to your plant. You sign the receipt for it, noting that the gauge on the tank reads 2000 psi. Several days later you notice that the gauge reads 1875 psi, indicating a leak. The storage room in which the cylinder is kept has a volume of 24.2 m3 and is very poorly ventilated. Calculate the maximum mole% of CO in the room at the time...
A chemical plant produces an ammonia-rich waste gas that cannot be released as-is into the environment....
A chemical plant produces an ammonia-rich waste gas that cannot be released as-is into the environment. One method to reduce the ammonia concentration in the waste gas is to bubble the waste gas through a liquid solvent. Components of the gas that are highly soluble, like ammonia, will dissolve into the liquid phase. Water is an appropriate liquid solvent for this process. The chemical plant produces 125.0 m3/hr of waste gas (ρ = 0.0407 mol/L) initially having a mole fraction...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT