Question

In: Statistics and Probability

A 1.6g amount of a paint sample was analyzed for lead content by a highly precise...

A 1.6g amount of a paint sample was analyzed for lead content by a highly precise method and 5.2% sampling RSD was obtained. This should be the sample weight to improve RSD to 3.1%

A) 0.57g

B) 2.7g

C)4.5g

D) None of the above

Solutions

Expert Solution

Option B is Correct

NOTE:: I HOPE THIS ANSWER IS HELPFULL TO YOU......**PLEASE SUPPORT ME WITH YOUR RATING......

**PLEASE GIVE ME "LIKE".....ITS VERY IMPORTANT  FOR,ME......PLEASE SUPPORT ME .......THANK YOU


Related Solutions

A 5.5984 g sample of soil was analyzed for lead. The sample was digested in hot...
A 5.5984 g sample of soil was analyzed for lead. The sample was digested in hot perchloric acid for 5 hours, cooled, filtered to remove insoluble silicates, transferred to a 250-ml volumetric flask and diluted to the mark with distilled water. A 50.00-ml portion of the resulting solution was treated with phosphoric acid (H3PO4) forming 0.0862 g of precipitate. What was the weight % of lead?                   3 Pb2+ + 2 PO43- ® Pb3(PO4)2(s)
A stainless steel alloy is to be analyzed for its chromium content. A 3.00 g sample...
A stainless steel alloy is to be analyzed for its chromium content. A 3.00 g sample of the steel is used to produce 250.0 mL of a solution containing Cr2O72−. A 10.0-mL portion of this solution is added to BaCl2(aq). When the pH of the solution is properly adjusted, 0.145 g BaCrO4(s)precipitates. What is the percent Cr, by mass, in the steel sample?​
A sample of wine was diluted 1:10 and analyzed for alcohol content. A calibration curve was...
A sample of wine was diluted 1:10 and analyzed for alcohol content. A calibration curve was created from a set of standard solutions producing a plot of absorbance vs. percent alcohol. The calibration curve had a slope of 8.07 x 10-2 with an intercept of 6.02 x 10-3. Keeping in mind that the wine sample was diluted by a factor of ten, what is the percent, by volume, of alcohol in your sample if the absorbance of your sample was...
A sample is analyzed to determine its iron content Fe2+ via a redox titration with potassium...
A sample is analyzed to determine its iron content Fe2+ via a redox titration with potassium chromate as the titrant. In the titration Fe2+ is oxidized to Fe3+ and CrO4 2- is reduced to Cr 3+. What is the percent by mass of iron in the sample if 0.9087g of the sample required 45.68mL of a 0.04322 M K2CrO4 solution to reach the endpoint? I worked out the balanced equation to be: 8H+ + 3Fe2+ + CrO4 2- = 3Fe3+...
Primary clarifier effluent was analyzed for solids content by an analytical laboratory. A 250-mL sample of...
Primary clarifier effluent was analyzed for solids content by an analytical laboratory. A 250-mL sample of the effluent was filtered through a laboratory (1 micrometer) filter. A 241-mL sample of the filtrate contained 89 mg of salts as dissolved solids (Residue 1). Solid residue from the filtration was dried overnight at 105 deg C and weighed 37 mg (Residue 2). What were the concentrations of total dissolved solids, total suspended solids, and total solids in the primary clarifier effluent? Water...
A water sample obtained from the neigborhood pond was analyzed for dissolved oxygen content. A volume...
A water sample obtained from the neigborhood pond was analyzed for dissolved oxygen content. A volume of 300 mL, with temperature 21 degrees Celsius, was analyzed using the Wrinkler method shown in the simulated lab material. It took 15.0 mL of 0.01 mol/L Na2S2O3 solution to reach titration end point. *Note: Na2S2O3 solution is the source of S2O32- ions for the titration reaction. In the succeeding questions, provide the following values required. Take note of the units a.What is the...
A 25.0-mL sample of lambic (a sour Belgian beer) was analyzed for its acetic acid content...
A 25.0-mL sample of lambic (a sour Belgian beer) was analyzed for its acetic acid content by an electrochemical method. The pure sample registered a signal of 2.55 mA. A standard solution of 0.500 mL of 0.109 M acetic acid was added, and the signal increased to 2.98 mA. What is the acetic acid concentration in the original lambic sample?
A 7.279 gram sample of meat was analyzed for its nitrogen content using kjeldahl method. Upon...
A 7.279 gram sample of meat was analyzed for its nitrogen content using kjeldahl method. Upon digestion, the ammonia liberated was collected in 250 ml of 0.855 M H3BO3. The resulting solution was titrated with 37.25 ml of 0.3122 M HCl using mixed indicator. Determine the % protein in the sample using 6.25 as a factor for meat product ? Answer: 13.98%
A 0.3999g sample of reagent grade Al2(SO4)3.xH2O was dissolved and analyzed for its aluminum content gravimetrically...
A 0.3999g sample of reagent grade Al2(SO4)3.xH2O was dissolved and analyzed for its aluminum content gravimetrically by precipitation as the aluminum oxinate complex, AL(C9H6NO)3, the precipitate weighing 0.4185g. Calculate the number of molecules of water of crystallization.
You wish to determine the amount of lead in a drinking water sample (500mL). It is...
You wish to determine the amount of lead in a drinking water sample (500mL). It is possible that sulfate in the sample (as well as other ions) will produce a matrix effect that will compromise the analysis, so you use a standard addition calibration method. You transfer 15 mL of your sample into each of five 50 mL volumetric flasks. You add the following volumes of a 5 ppm lead standard to the 5 flasks : 0, 5, 10, 15,...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT