Question

In: Statistics and Probability

Two quality control technicians measured the surface finish of a metal part. Measurements are in the...

Two quality control technicians measured the surface finish of a metal part. Measurements are in the following table. Assume that the data are normally distributed. (a) State and test the hypothesis that the mean surface finish measurements made by the two technicians are equal at alpha = 0.05 assuming equal variances. (b) State and test the hypothesis that the variances are equal at alpha = 0.05 to verify the assumption of equal variances. Explains the steps to complete this using minitab.

Tech 1 Tech 2
1.45 1.64
1.41 1.47
1.21 1.76
1.54 1.57
1.48 1.20
1.31 1.29
1.34 1.37
1.38 1.45

Solutions

Expert Solution

-----------------------------------------------------------------------------------------------------------------------------

------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------


Related Solutions

Two quality control technicians measured the surface finish of a metal part, obtaining the data shown....
Two quality control technicians measured the surface finish of a metal part, obtaining the data shown. Assume that the measurements are normally distributed. Use Minitab© for all tests and calculations. Tech 1 1.45 1.37 1.21 1.54 1.48 1.29 1.34 * Tech 2 1.54 1.41 1.56 1.37 1.20 1.31 1.27 1.35 a) Does the normality assumption seem reasonable for the data? Are the variances equal? How do you know? b) The supervisor asks you to test the hypothesis that the difference...
Two quality control t echnicians measured the surface finish of a metal part, obtaining the data...
Two quality control t echnicians measured the surface finish of a metal part, obtaining the data in Table 4E.1. Assume that the measurements are normally distributed. Technician 1: (1.45, 1.37,1.21,1.54,1.48,1.29,1.34) Technican 2: ( 1.54, 1.41, 1.56, 1.37, 1.20 ,1.31, 1.27, 1.35 ) (d) Test the hypothesis that the variances of the measurements made by the two technicians are equal. Use What are the practical implications if the null hypothesis is rejected? (e) Construct a 95% confidence interval estimate of the...
Two Ways ANOVA An engineer suspects that the surface finish of a metal part is influenced...
Two Ways ANOVA An engineer suspects that the surface finish of a metal part is influenced by the feed rate and the depth of cut. She selects three feed rates and four depths of cut. She then conducts a factorial experiment and obtains the following data: (Use Minitab) Depth of Cut (in) Feed Rate (in/min) 0.15 0.18 0.20 0.25 74 79 82 99 0.20 64 68 88 104 60 73 92 96 92 98 99 104 0.25 86 104 108...
An engineer suspects that the surface finish of a metal part is influenced by the feed...
An engineer suspects that the surface finish of a metal part is influenced by the feed rate and the depth of cut. He selects three feed rates and four depths of cut. He then conducts a factorial experiment and obtains the following data: Depth of Cut (in) Feed Rate (in/min) 0.15 0.18 0.20 0.25  74  79  82  99 0.20  64  68  88 104  60  73  92  96  92  98  99 104 0.25  86 104 108 110  88  88  95  99  ...
A quality control inspector is interested in maintaining a flatness specification for the surface of the metal disks.
A quality control inspector is interested in maintaining a flatness specification for the surface of the metal disks. Thirty flatness measurements. in (0.001 inch) were collected. Which probability density model - normal, lognormal, or Weibull - appears to provide the most suitable fit to the data? 2.49 2.14 1.63 4.46 3.69 4.58 1.28 1.28 1.59 0.82 2.23 7.55 2.20 4.78 5.24 1.54 3.81 2.13 1.45 2.21 6.65 6.40 2.06 4.06 2.66 1.66 2.38 6.04 2.85 3.70 Identify the associated parameter...
The Quality Control Department employs five technicians during the day shift. Listed below is the number...
The Quality Control Department employs five technicians during the day shift. Listed below is the number of times each technician instructed the production foreman to shut down the manufacturing process last week. Technician Shutdowns Taylor 4 Hurley 2 Gupta 4 Rousche 3 Huang 2 How many different samples of two technicians are possible from this population? List all possible samples of two observations each and compute the mean of each sample. (Round your answers to 1 decimal place.) Compare the...
Two different technicians (Tech A and Tech B) each measured the cardiac output for a sample...
Two different technicians (Tech A and Tech B) each measured the cardiac output for a sample of 26 patients using Doppler Echocardiography. The supervisor would like to use this paired data to assess inter-rater reliability by testing if the population mean difference in cardiac output is 0 (no difference on average) versus the alternative that there is a difference. The hypotheses to be tested are:  H0: μd = 0versus Ha: μd ≠ 0, using a 10% significance level. A- The sample...
The thickness of a metal part is an important quality parameter. Data on thickness (in inches)...
The thickness of a metal part is an important quality parameter. Data on thickness (in inches) are given in the following table, for 25 samples of five parts each. Sample Number x1 x2 x3 x4 x5 1 0.0629 0.0636 0.0640 0.0634 0.0641 2 0.0630 0.0632 0.0620 0.0624 0.0627 3 0.0628 0.0631 0.0633 0.0633 0.0630 4 0.0634 0.0630 0.0631 0.0632 0.0633 5 0.0619 0.0628 0.0630 0.0619 0.0625 6 0.0613 0.0629 0.0634 0.0625 0.0628 7 0.0630 0.0639 0.0625 0.0629 0.0627 8 0.0628...
3.32. Quality Control. An automatic machine in a small factory produces metal parts. Most of the...
3.32. Quality Control. An automatic machine in a small factory produces metal parts. Most of the time (90% according to long-term records), it produces 95% good parts, while the remaining parts have to be scrapped. Other times, the machine slips into a less productive mode and only produces 70% good parts. The foreman observes the quality of parts that are produced by the machine and wants to stop and adjust the machine when she believes that the machine is not...
The quality control department of John Deere measured the length of 100 bolts randomly selected from...
The quality control department of John Deere measured the length of 100 bolts randomly selected from a specified order. The mean length was found to be 9.75 cm, and the standard deviation was 0.01 cm. if the bolt lengths are normally distributed, find: a) The percentage of bolts shorter than 9.74 cm b) The percentage of bolts longer than 9.78 cm c) The percentage of bolts that meet the length specification of 9.75 +/- 0.02 cm d) The percentage of...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT