A load draws between 100mA and 400mA at 6V. It is receiving power from an unregulated...

A load draws between 100mA and 400mA at 6V. It is receiving power from an unregulated DC power supply whose output voltage can vary between 8.5V and 12V. Design a Zener diode voltage regulator using a 6V Zener diode that regulates for diode currents greater than 4mA and has a maximum power rating of 6W. Show the circuit diagram for the completed design and specify the power rating for all components.

Expert Solution

The solution to the problem goes in this way that first we have listed the given parameters which are given in the question then we have seen the circuit diagram containing various components that are required to build the regulator and finally we have calculated the various parameters values. Refer the images shown below:

Manojponduru answered 2 years ago

A load draws 3500 W of power at a lagging PF of 0.6 from 500-Vrms, 120...

A load draws 3500 W of power at a lagging PF of 0.6 from 500-Vrms, 120 Hz sinusoidal source. a. (8) Calculate the complex power consumed by the load. b. (10) Calculate the capacitance needed to correct the power factor to 0.8 lagging. c. (7) Draw the power triangles to reflect power system before and after the PF correction. Label all sides and power angles numerically.

c) A 3-phase load draws an apparent power of 80kVA from a 415V 3-phase supply. The...

c) A 3-phase load draws an apparent power of 80kVA from a 415V 3-phase supply. The power factor of the load is 0.85. Determine the real power supplied to the load and the rms line current? D) Explain the importance of energy storage for grids that have large amounts of wind power. Name one type of storage system used within a large electricity grid. E) Explain why AC loads are often rated in terms of their apparent power (VA), rather...

A single phase motor load draws 5.5 A of current at a 0.83 power factor lagging...

A single phase motor load draws 5.5 A of current at a 0.83 power factor lagging from a 50 Hz 240 V source. A capacitor is connected in parallel to the motor to improve the power factor. (a)If the power factor is improved to unity, find the value of capacitance of the capacitor. (b)If the power factor improves to 0.96, find the value of capacitance of the capacitor. PreviousNext

3. A 60Hz, single phase line transmits power to an inductive load that has a receiving...

3. A 60Hz, single phase line transmits power to an inductive load that has a receiving voltage of 13.8KV, reactive factor of 0.6 and 5 MVA respectively. If this line has a impedance of 1+j2 ohms per conductor, Calculate the following: The voltage at the sending end (10 pts) b. The transmission line efficiency (10 pts) c. If this line is connected in parallel to a telephone wire and the conductors of the power line is labelled a and b...

Fundamental of power electronics: In a certain application, an unregulated dc input voltage can vary between...

Fundamental of power electronics: In a certain application, an unregulated dc input voltage can vary between 18 and 36 V. It is desired to produce a regulated output of 28 V to supply a 2 A load. control circuit automatically adjust D to maintain the constant output voltage and current. All ideal components. Hence, a converter is needed that is capable of both increasing and decreasing the voltage. Since the input and output voltages are both positive, converters that invert the...

THESE ARE QUESTION FROM THE TOPIC VARIABLE LOAD ON POWER STATIONS FROM THE SUBJECT POWER SYSTEM...

THESE ARE QUESTION FROM THE TOPIC VARIABLE LOAD ON POWER STATIONS FROM THE SUBJECT POWER SYSTEM FUNDAMENTALS PLEASE DO THE QUESTIONS STEP BY STEP AND IN NEAT HAND WRITTING THE ANSWERS ARE GIVEN WITH THE QUESTIONS 1) A generating station has a connected load of 40 MW and a maximum demand of 20 MW : the units generated being 60 × 106. Calculate (i) the demand factor (ii) the load factor. ANS [(i) 0·5 (ii) 34·25%] 2) A 100 MW...

Estimate the total power that your household draws from DTE, in one month. Then, if possible,...

Estimate the total power that your household draws from DTE, in one month. Then, if possible, compare the total power (in kWh) to the actual power that you were billed, last month. To successfully "compare" the numbers, you should determine the percent difference between your estimated power and the actual power that your household payed for last month. You should show how you estimated your total power and your percent difference calculation. Note: DTE bills you in kWh. This stands...

a.) Define constant power load (CPL) and constant voltage load (CVL). Are power electronics devices constant...

a.) Define constant power load (CPL) and constant voltage load (CVL). Are power electronics devices constant power loads? If so, explain why. b) How can Zener diodes work as voltage stabilizer? c) Mention the typical value of resistance (Ohm-m) and conductance (Siemens/meter) for conductors, semiconductors and insulators.

The complex power absorbed by a load is S= 850∠-25⁰. This means the load is ________...

The complex power absorbed by a load is S= 850∠-25⁰. This means the load is ________ and pf is___________(a) Inductive , lagging(b) Inductive, leading(c) Capacitive, lagging(d) Capacitive, leading The answer is D but why

For a large number of independent draws from a box, will standard deviation, range of draws...

For a large number of independent draws from a box, will standard deviation, range of draws and proportion of 1's in draws from a 0-1 box have a normally distributed probability histogram?

Question