3. a) Draw a schematic diagram of an X-ray diffractometer. [4 marks] b) The results of...

3. a) Draw a schematic diagram of an X-ray diffractometer. [4 marks]

b) The results of an X-ray diffraction experiment that used X-rays of wavelength 0.154 nm show the first 6 peaks at angles of 40.6°, 58.8°, 73.8°, 87.8°, 101.8°, and 116.4°.

i) Use this information to determine the possible crystal structures of the sample. [10 marks]

ii) An additional scan was performed on the sample and an additional peak was observed at an angle of 133.2°. Determine the crystal structure of the sample. [3 marks]

iii) Calculate the Miller indices for each of the measured peaks. [7 marks]

iv) Draw the orientation of the crystal plane within the unit cell corresponding to the peak at 101.8°. [3 marks]

v) Calculate the lattice constant and identify the sample. [3 marks]

Expert Solution

genius_generous answered 2 years ago

Draw a schematic diagram and a context diagram for a standard blender. Identify all of the...

Draw a schematic diagram and a context diagram for a standard blender. Identify all of the external entities and label all of the interactions.

Draw bifurication diagram of: (x^2-a)(x^2-4)

1. Describe the process of Schematic Capture. 2. What is a Schematic Diagram. 3. Describe the...

1. Describe the process of Schematic Capture. 2. What is a Schematic Diagram. 3. Describe the guidelines for drawing schematics. 4. List the three main types of libraries for PCB design. 5. How are components classified, based on the leads.

Define Electrodialysis (ED), draw a schematic diagram of the process, and determine the main characteristics of...

Define Electrodialysis (ED), draw a schematic diagram of the process, and determine the main characteristics of ion exchange membranes to be used. What are the process limitations in ED systems? then differentiate between dialysis and osmosis phenomena.

draw a schematic diagram of an activated sludge system that includes a "selector". describe the function...

draw a schematic diagram of an activated sludge system that includes a "selector". describe the function of the "selector" and describe how this process configuration and associated operating strategy is different from a "conventional" activated sludge system.

3. (a) Outline with the aid of a schematic diagram the different stages in the processing...

3. (a) Outline with the aid of a schematic diagram the different stages in the processing of an Interstitial Free strip steel (b) Discuss the principles of the pearlite transformation in a eutectoid (0.76%wt C) plain carbon steel (c) List four main mechanisms and microstructural features which contribute to the high strength of martensite in marageing steels

a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with...

a) Draw and label your own circuit diagram using standard schematic symbols for a circuit with a 12 V battery, a 15 ohm resistor, a 400 mH inductor, and a switch, all in series. b) Write a diffferential equation (in the form of a loop equation) describing the behavior of this circuit after the switch is closed. c) The switch is first closed at time t = 0. Write down an equation for current in the circuit as a function...

Draw the schematic diagram of circuit which realizes function F=x'y'z+xz by using 3 input active-0 output...

Draw the schematic diagram of circuit which realizes function F=x'y'z+xz by using 3 input active-0 output DECODER and necessary AND, OR, EXOR and NOT gates.

A bubble of air is suspended underwater. Draw a ray diagram showing the approximate path followed...

A bubble of air is suspended underwater. Draw a ray diagram showing the approximate path followed by a light ray passing from the water (a) through the upper half of the bubble, (b) through its center, and (c) through its lower half. Does the bubble act like a converging or diverging lens? Explain.

Design a DISC BRAKE based on the given below. Draw schematic diagram and show complete solutions/computations...

Design a DISC BRAKE based on the given below. Draw schematic diagram and show complete solutions/computations with direct subtitution. Also compute for the forces involved in the system. GIVEN: Braking Force (HP) = 15 HP N (RPM) = 1800 RPM

Question