A capacitor is constructed in the following way: a 1:00m2 layer of conductor, followed by a...

A capacitor is constructed in the following way: a 1:00m2 layer of conductor, followed by a 0:20mm thick 1:00m2 layer of fused quartz, followed by a 1:00m2 layer of conductor, followed by a 0:40mm thick 1:00m2 layer of pyrex, followed by a 1:00m2 layer of conductor.

(a) Calculate the capacitance of this capacitor.

(b) Calculate the potential across each of your individual capacitors if you apply 5V across the entire capacitor.

(d) If I continually raise the voltage across the capacitor, which dielectric will break down first? At what voltage does this occur?

Solutions

Expert Solution

genius_generous answered 1 year ago

Next > < Previous

Related Solutions

1. How is a capacitor physically constructed?

RC circuit. The time constant 1. How is a capacitor physically constructed?2. How is the unit of capacity defined?3. What is the electrical symbol of a capacitor?4. What physical factors determine and affect the capacitance of a capacitor?5. How is the time constant of an RC circuit defined?

semi-conductor diode is constructed by placing an n-type semi-conductor together with a p-type semi-conductor. When the n...

semi-conductor diode is constructed by placing an n-type semi-conductor together with a p-type semi-conductor. When the n and p sides are first brought together, electrons in the [1. (A) valence, (B) condition, (C) heavy metal] band of the [2. (A) n, (B) p] side fall into the holes in the [3. (A) valence, (B) condition, (C) heavy metal] band of the [4. (A) n (B) p] side, creating a depletion zone (a region of [5. (A) increased, (B) decreased, (C) unchanged]...

A furnace wall is constructed of an inner layer of 10 mm of material A with...

A furnace wall is constructed of an inner layer of 10 mm of material A with kA = 20W/mK, 20 mm of material B with kB = 1.5 W/mK, a middle layer of 30 mm of material C with kC=3.0 W/mK) , and an outer layer of 40 mm of material D (kD=300 W/mK) . The temperature of inside wall is 1000 K and the temperature of outer layer is 350 K. The temperature and convection coefficient of hot air...

A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The...

A circuit is constructed with an AC generator, a resistor, capacitor and inductor as shown. The generator voltage varies in time as ε =Va - Vb = εmsinωt, where εm = 120 V and ω = 231 radians/second. The inductance L = 155 mH. The values for the capacitance C and the resistance R are unkown. What is known is that the current in the circuit leads the voltage across the generator by φ = 49 degrees and the average...

A circuit is constructed with four resistors, one capacitor, onebattery and a switch as shown....

A circuit is constructed with four resistors, one capacitor, one battery and a switch as shown. The values for the resistors are: R1 = R2 = 32 Ω, R3 = 90 Ω and R4 = 89 Ω. The capacitance is C = 85 μF and the battery voltage is V = 12 V. The positive terminal of the battery is indicated with a + sign.1) The switch has been open for a long time when at time t = 0,...

A flat furnace wall is constructed of a 4.5 in (114 mm) layer of Silo-cel brick,...

A flat furnace wall is constructed of a 4.5 in (114 mm) layer of Silo-cel brick, with a thermal conductivity of 0.08 Btu/ft·h·˚F (0.138 W/m·˚C), backed by a 9-in. (229-mm) layer of common brick, of conductivity 0.8 Btu/ft·h·˚F(1.38 W/m.˚C). The temperature of the inner face of the wall is 1400˚F (760˚C), and that of the outer face is 170˚F(76.6˚C). (a) What is the heat loss through the wall? (b) What is the temperature of the interface between the refractory brick...

Q2. Assume a rigid strip footing is constructed on a normally consolidated clay layer under a...

Q2. Assume a rigid strip footing is constructed on a normally consolidated clay layer under a uniformly distributed vertical load. The depth of footing is zero and the water table is a few metres below the surface ground. The average shear strength parameters of the clay layer are: At the beginning of loading: fu = 0, cu = 50 kPa Long time after loading:, f’ = 25° and c’ = 0 kPa Will the bearing capacity of this footing change,...

Please distinguish between the following terms. 1) Intrinsic semi-conductor and extrinsic semi-conductor 2) Conduction band and...

Please distinguish between the following terms. 1) Intrinsic semi-conductor and extrinsic semi-conductor 2) Conduction band and valence band 3) Dark current and read noise 4) Quantum efficiency and detective quantum efficiency 5) overscan and bias frame 6) dome-flat and twilight-flat

Statistics based on polls can be faulty if the poll is constructed in such a way...

Statistics based on polls can be faulty if the poll is constructed in such a way as to encourage a particular answer. If a question is worded "Do you feel you should be taxed so some people can get paid for staying home and doing nothing?" it is likely to get a lot of "no" responses. On the other hand, the question "Do you think the government should help people who are unable to find work?" is likely to get...

For the question as followed, just write the formula and the way you solve the problem:...

For the question as followed, just write the formula and the way you solve the problem: 1. Given a chart a, size = 50 (i.e. 50 values in chart a), and the range of the chart a is given Divide the range into N = 10 equal-length segments (hereafter called “bins”) and for each bin, find its bound (aj , bj ) as well as its center cj for j = 1, 2,..., 10. 2. Sort the data and place...

Subjects