Question

In: Mechanical Engineering

Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 =...

Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic efficiencies of the compressor and turbine are 83 and 87%, respectively. The compressor pressure ratio is 16 and the temperature at the turbine inlet is 2500°R. The volumetric flow rate of the air entering the compressor is 9000 ft3/min. Use an air-standard analysis.

Determine all temperatures at each state.

A) Determine the net power developed, in Btu/h.

B) Determine the thermal efficiency of the cycle

C) the temperatures at the compressor and turbine exits in °R

Solutions

Expert Solution

Hello there. I have initially converted data into SI units because it is easier to deal with SI units. But final answers I have given in required units only. Please find the attached solution.

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 =...
Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic efficiencies of the compressor and turbine are 83 and 87%, respectively. The compressor pressure ratio is 16 and the temperature at the turbine inlet is 2500°R. The volumetric flow rate of the air entering the compressor is 9000 ft3/min. Use an air-standard analysis. Determine the net power developed, in Btu/h.
Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 =...
Air enters the compressor of a simple gas turbine at p1 = 14 lbf/in2, T1 = 520°R. The isentropic efficiencies of the compressor and turbine are 83 and 87%, respectively. The compressor pressure ratio is 16 and the temperature at the turbine inlet is 2500°R. The volumetric flow rate of the air entering the compressor is 9000 ft3/min. Use an air-standard analysis. Determine the net power developed, in Btu/h.
Refrigerant 134a at p1 = 30 lbf/in2, T1 = 40oF enters a compressor operating at steady...
Refrigerant 134a at p1 = 30 lbf/in2, T1 = 40oF enters a compressor operating at steady state with a mass flow rate of 400 lb/h and exits as saturated vapor at p2 = 160 lbf/in2. Heat transfer occurs from the compressor to its surroundings, which are at T0 = 40oF. Changes in kinetic and potential energy can be ignored. The power input to the compressor is 4 hp.   Determine the heat transfer rate for the compressor, in Btu/hr, and the...
13.75 Air enters the compressor of a simple gas turbine power plant at 70F, 1 atm,...
13.75 Air enters the compressor of a simple gas turbine power plant at 70F, 1 atm, is compressed adiabatically to 40 lbf/in.2, and then enters the combustion chamber where it burns completely with propane gas (C3H8) entering at 77F, 40 lbf/in.2and a molar flow rate of 1.7 lbmol/h. The combustion products at 1340F, 40 lbf/in.2 enter the turbine and expand adiabatically to a pressure of 1 atm.The isentropic compressor efficiency is 83.3% and the isentropic turbine efficiency is 90%. Determine...
. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C,...
. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C, 1.0133 bar and is compressed through a pressure ratio of 10. The air leaving the compressor passes through a heat exchanger before entering the combustion chamber. The hot gases leave the combustion chamber at 800 ?C and expand through an HP turbine which drives the compressor. On leaving the HP turbine the gases pass through a reheat combustion chamber which raises the temperature of...
. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at...
. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at 14.5 psia and 540° R. The pressure ratio across the turbine and compressor is same, which is equal to 6. Assume that the compressor work as 0.4 times the turbine work. Take K=1.4 a) Draw the T-S diagram of the cycle. [2] b) Calculate the maximum temperature in the cycle. [3] c) Calculate the cycle efficiency
Seven lbm of ammonia in a piston-cylinder assembly, initially at p1 = 60 lbf/in2 and T1...
Seven lbm of ammonia in a piston-cylinder assembly, initially at p1 = 60 lbf/in2 and T1 = 120 (one hundred twenty) oF, undergoes an isobaric process to a final state. The work done on a system is 90 Btu. At the final state, determine the temperature (in oF) and the quality of ammonia.
Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 25°C...
Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 25°C with a low velocity and exits at 1 MPa and 347°C with a velocity of 90 m/s. The compressor is cooled at a rate of 1500 kJ/min, and the power input to the compressor is 235 kW. Determine the mass flow rate of air through the compressor. The inlet and exit enthalpies of air are 298.2 kJ/kg and 628.07 kJ/kg. The mass flow rate...
Air enters a compressor operating at steady state with a pressure of 14.7 lbf/in.2, a temperature...
Air enters a compressor operating at steady state with a pressure of 14.7 lbf/in.2, a temperature of 70°F, and a volumetric flow rate of 500 ft3/min. The air velocity in the exit pipe is 700 ft/s and the exit pressure is 133 lbf/in.2 If each unit mass of air passing from inlet to exit undergoes a process described by pv1.34 = constant, determine (a) the exit temperature, in °F, and (b) the diameter of the exit pipe, in inches.
Water at p1 = 20 bar, T1 = 400oC enters a turbine operating at steady state...
Water at p1 = 20 bar, T1 = 400oC enters a turbine operating at steady state and exits at p2 = 1.5 bar, T2 = 220oC. The water mass flow rate is 4000 kg/hour. Stray heat transfer and kinetic and potential energy effects are negligible. Determine the power produced by the turbine, in kW, and the rate of entropy production in the turbine, in kW/K.
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT