Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 25°C...

Air enters the compressor of a gas-turbine plant at ambient conditions of 100 kPa and 25°C with a low velocity and exits at 1 MPa and 347°C with a velocity of 90 m/s. The compressor is cooled at a rate of 1500 kJ/min, and the power input to the compressor is 235 kW. Determine the mass flow rate of air through the compressor. The inlet and exit enthalpies of air are 298.2 kJ/kg and 628.07 kJ/kg.

The mass flow rate of air is kg/s.

Expert Solution

Colby Messinger answered 2 years ago

. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C,...

. In a gas turbine plant, air enters a compressor at atmospheric conditions of 15 ?C, 1.0133 bar and is compressed through a pressure ratio of 10. The air leaving the compressor passes through a heat exchanger before entering the combustion chamber. The hot gases leave the combustion chamber at 800 ?C and expand through an HP turbine which drives the compressor. On leaving the HP turbine the gases pass through a reheat combustion chamber which raises the temperature of...

. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at...

. Air enters the compressor of a gas turbine power plant operating on Brayton cycle at 14.5 psia and 540° R. The pressure ratio across the turbine and compressor is same, which is equal to 6. Assume that the compressor work as 0.4 times the turbine work. Take K=1.4 a) Draw the T-S diagram of the cycle. [2] b) Calculate the maximum temperature in the cycle. [3] c) Calculate the cycle efficiency

Air enters the compressor of an ideal gas refrigeration cycle at 17°C and 35 kPa and...

Air enters the compressor of an ideal gas refrigeration cycle at 17°C and 35 kPa and the turbine at 47°C and 160 kPa. The mass flow rate of air through the cycle is 0.3 kg/s. Assume variable specific heats for air. Determine the net power input. The net power input is kW.

13.75 Air enters the compressor of a simple gas turbine power plant at 70F, 1 atm,...

13.75 Air enters the compressor of a simple gas turbine power plant at 70F, 1 atm, is compressed adiabatically to 40 lbf/in.2, and then enters the combustion chamber where it burns completely with propane gas (C3H8) entering at 77F, 40 lbf/in.2and a molar flow rate of 1.7 lbmol/h. The combustion products at 1340F, 40 lbf/in.2 enter the turbine and expand adiabatically to a pressure of 1 atm.The isentropic compressor efficiency is 83.3% and the isentropic turbine efficiency is 90%. Determine...

Air enters the compressor at 100 kPa, 300 K and is compressed to 1000 kPa. The...

Air enters the compressor at 100 kPa, 300 K and is compressed to 1000 kPa. The temperature at the inlet to the first turbine stage is 1400 K. The expansion takes place isentropically in two stages, with reheat to 1400 K between the stages at a constant pressure of 300 kPa. A regenerator having an effectiveness of 100% is also incorporated into the cycle. The turbine and the compressor each have am isentropic efficiency of 80%. Determine the following: (a.)...

Air enters the turbine of a gas turbine at 1400 kPa, 1400 K, and expands to...

Air enters the turbine of a gas turbine at 1400 kPa, 1400 K, and expands to 100 kPa in two stages. Between the stages, the air is reheated at a constant pressure of 350 kPa to 1400 K. The expansion through each turbine stage is isentropic. Determine: (b) the heat transfer for the reheat process, in kJ/kg of air flowing. (c) the increase in net work as compared to a single stage of expansion with no reheat.

An adiabatic air compressor with inlet conditions of 100 kPa, 27 C and an exit pressure...

An adiabatic air compressor with inlet conditions of 100 kPa, 27 C and an exit pressure of 500 kPa has an inlet volume flow rate of 5 m3/s and operates in steady flow. Calculate the minimum power required to drive the compressor.

Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290...

Air enters the compressor of an ideal air standard Brayton cycle at 100 kPa and 290 K with a mass flow rate (m⋅) of 6 kg/s. The compressor pressure ratio is 10. The turbine inlet temperature is 1500 K. If a regenerator with an effectiveness of 70% is incorporated in the cycle, determine (a) the thermal efficiency (ηth,Brayton) of the cycle. Use the PG model for air. (b) What-if Scenario: What would the thermal efficiency be if the regenerator effectiveness...

. Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa...

. Air enters the compressor of an ideal gas refrigeration cycle at 7oC and 40 kPa and the turbine at 37oC and 170 kPa. The mass flow rate of air through the cycle is 0.3 kg/sec. Assuming variable specific heats for air, determine (a) the rate of refrigeration, (b) the net power input, and (c) the coefficient of performance. Also, draw the T-s diagram of the gas refrigeration cycle.

Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of...

Air enters an adiabatic compressor at 100 kPa (absolute) and 20 ºC at a rate of 0.075 m3 /s, and it exits at a pressure of 900 kPa (absolute). The compressor has an isentropic efficiency of 70 percent. Neglecting the changes in kinetic and potential energies, determine (a) the exit temperature of air and (b) the power required to drive the compressor.

Question