Question

In: Physics

Specimen ID ms, g mw, g Tw initial, 0C Twfinal, 0C DTw, 0C DTs, 0C Qw,...

Specimen ID

ms, g

mw, g

Tw initial, 0C

Twfinal, 0C

DTw, 0C

DTs, 0C

Qw, cal

cs, cal/gC0

A

89.7

118.4

21

26

B

91.2

153.1

21

30

C

89.4

124.2

21

26.5

D

90.3

115.8

21

26.5

E

90.8

121.5

21

25.7

mcup = ___19.6______ g

Analysis:

  • Here are the accepted values for the specific heat of each specimen:

A: Zinc, specific heat = 0.093

B: Aluminum, specific heat = 0.210

C: Iron, specific heat = 0.110

D: Copper, specific heat = 0.093

E: Brass, specific heat = 0.090

  • Calculate the % errors for each of your ‘c’ values.

Solving for cs, the specific heat of the unknown specimen,

  • The following measurements are given in the data table below: mass of the Styrofoam cup, mass of the specimen, mass of the water, initial and final temperature of the water.

Calculate: the change in temperature of the water, the change in temperature of the specimen (it starts at the boiling point of water, 100 degrees C), the total heat transferred to the water, and the specific heat of the specimen.

Solutions

Expert Solution


Related Solutions

A 0.7257 g mixture of KCN (MW = 65.116 g/mol) and NaCN (MW = 49.005 g/mol)...
A 0.7257 g mixture of KCN (MW = 65.116 g/mol) and NaCN (MW = 49.005 g/mol) was dissolved in water. AgNO3 was added to the solution, precipitating all the CN– in solution as AgCN (MW = 133.886 g/mol). The dried precipitate weighed 1.650 g. Calculate the weight percent of KCN and NaCN in the original sample.
1. A 450-g ball of copper at 20 0C is placed in a pot of boiling...
1. A 450-g ball of copper at 20 0C is placed in a pot of boiling water until equilibrium is reached. How much thermal energy is absorbed by the ball?[ specific heat of copper = 385.1 J/Kg 0C] 2. A 100-g mass of an unknown material at 100 0C is placed in an aluminum calorimeter of 60.0 g that contains 150 g of water at an initial temperature of 20.0 0C. The final temperature is observed to be 21.5 0C....
A sample containing a mixture of SrCl2·6H2O (MW = 266.62 g/mol) and CsCl (MW = 168.36...
A sample containing a mixture of SrCl2·6H2O (MW = 266.62 g/mol) and CsCl (MW = 168.36 g/mol) originally weighs 1.7215 g. Upon heating the sample to 320 °C, the waters of hydration are driven off SrCl2·6H2O, leaving the anhydrous SrCl2. After cooling the sample in a desiccator, it has a mass of 1.2521 g. Calculate the weight percent of Sr, Cs, and Cl in the original sample.
If you are given the following solids: Na3PO4             MW = 163.94 g/mol K3PO4                  MW = 212.26
If you are given the following solids: Na3PO4             MW = 163.94 g/mol K3PO4                  MW = 212.26 g/mol    NaH2PO4           MW = 119.98 g/mol K2HPO4             MW = 174.17 g/mol Na2HPO4           MW = 141.96 g/mol KH2PO4             MW = 136.08 g/mol Which compounds would you use to prepare your stock solutions? Why? I picked KH2PO4 and K2HPO4 because potassium salts dissolve more readily in H2O which would make the lab go more smoothly. I would like to know if I'm missing any...
A 50 g ice cube initially at - 30 0C is heated until it has completely...
A 50 g ice cube initially at - 30 0C is heated until it has completely been changed to steam at 120 0C, how much heat energy in calories has been added? ( Specific heat of ice is 0.5 ca/g 0C and that of steam is 0.48 cal/ g 0C , that of water is 1 cal/g 0C ; Latent heat of fusion of ice is 80 cal/g, Latent haet of vaporization is 540 cal/g ).
MW (g/mol) / MP ( oC) / Solubility in cold H2O (g / 100 mL) /...
MW (g/mol) / MP ( oC) / Solubility in cold H2O (g / 100 mL) / Solubility in boiling H2O (g / 100 mL) Acetanilide 135.2 / 114 / 0.54 / 5.0 Phenacetin 179.2 / 135 / 0.076 / 1.22 Using solubility data in the table of reagents, calculate the minimum amount water needed to recrystallize: i. 1.5 g of phenacetin. ii. 1.5 g of acetanilide. b. If the minimum amount of water needed is used, how many grams of...
3.920 g of sodium acetate ( CH3COONa MW= 82.03 g/mol), is dissolved in 235.0ml of H2O...
3.920 g of sodium acetate ( CH3COONa MW= 82.03 g/mol), is dissolved in 235.0ml of H2O at 50 degree celsius (kw= K.48E-14). Calculate the pH of this soluion ( Ka= 1.63 E-5) Determine the % ionization
4. The following data were obtained from a creep test for a specimen having an initial...
4. The following data were obtained from a creep test for a specimen having an initial gage length of 2.0 in. and an initial diameter of 0.6 in. The initial stress applied to the material is 10,000 psi. The diameter of the specimen after fracture is 0.52 in. Length Between Gage Marks ( (in.) Time (h) Strain (in./in.) 2.004 0 0.002 2.01 100 0.004 2.02 200 0.006 2.03 400 0.008 2.045 1000 0.012 2.075 2000 0.020 2.135 4000 0.035 2.193...
What is the reaction A(g) + B(g) + C(g)------------> D(g) Experiment Initial [A] (mol/L) Initial [B]...
What is the reaction A(g) + B(g) + C(g)------------> D(g) Experiment Initial [A] (mol/L) Initial [B] (mol/L) Initial [C] (mol/L) Initial rate (M/s) 1 0.0500 0.0500 0.0100 6.25*^(-3) 2 0.1000 0.0500 0.0100 1.25*^(-2) 3 0.1000 0.1000 0.0100 5*10^(-2) 4 0.0500 0.0500 0.0200 6.25*10^(-3) 1) What is the order with respect to each reactant? 2) Write the rate law 3) Calculate K (using the data from experiment 1)
A 100.0 mL solution containing 0.830 g of maleic acid (MW = 116.072 g/mol) is titrated...
A 100.0 mL solution containing 0.830 g of maleic acid (MW = 116.072 g/mol) is titrated with 0.298 M KOH. Calculate the pH of the solution after the addition of 48.0 mL of the KOH solution. Maleic acid has pKa values of 1.92 and 6.27. pH = At this pH, calculate the concentration of each form of maleic acid in the solution at equilibrium. The three forms of maleic acid are abbreviated H2M, HM–, and M2–, which represent the fully...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT