Question
In: Mechanical Engineering
Estimate the axial infinite fatigue strength (10⁶) and 10³ fatigue strength for a 25 mm diameter...
Estimate the axial infinite fatigue strength (10⁶) and 10³
fatigue strength for a 25 mm diameter reversed axially loaded steel
bar having Su =950 Mpa, Sy = 600 Mpa and is made from a “cold
drawn” steel.
Assume: T< 840º F, 99 % Reliability, CG = .8
Solutions
Expert Solution
For 10^6 cycles fatigue strength is 186.96 MPa
For 10 ^3 cycles fatigue strength is 712.5 MPa
samet mamat answered 2 hours agoRelated Solutions
1) Determine unmodified fatigue strength (units = MPa) of hot-rolled 1030 steel shaft in axial loading...
1) Determine unmodified fatigue strength (units = MPa) of
hot-rolled 1030 steel shaft in axial loading for a design life of
10,000 cycles. Do not apply any fatigue correction factors. SN
__________ MPa
2) Determine unmodified fatigue strength (units = ksi) for a
normalized 4130 steel shaft in bending for a design life of 10^7
cycles. Do not apply any fatigue correction factors. SN __________
ksi
3) Determine unmodified fatigue strength (units = MPa) for
cold-rolled 3003 aluminum rod in...
Question: A cylindrical rock sample with a diameter of 54 mm in the uniaxial compressive strength...
Question: A cylindrical rock sample with a
diameter of 54 mm in the uniaxial compressive strength test
It was broken by applying a force of 160.2 kN. Since the angle
between the applied load direction and the breaking surface is 30
°, the stresses acting on the breaking surface;
(a) Solve using the Mohr diagram (graphic
method).
(b) Solve by analytical method.
Air at 25°C flows over a 10-mm-diameter sphere with a velocity of 20 m/s, while the...
Air at 25°C flows over a 10-mm-diameter sphere with a velocity
of 20 m/s, while the surface of the sphere is maintained at 75°C.
What is the rate of heat transfer from the sphere? q = ___ W ?
Please provide correct final answer for guaranteed
thumbs up rating !
The mean diameter of the square threaded screw having pitch of 10 mm is 50 mm....
The mean diameter of the square threaded screw having pitch of
10 mm is 50 mm. A load of 20 kN is lifted through a distance of 170
mm. Find the work done in lifting the load and the efficiency of
the screw, when
1. The load rotates with the screw, and
2. The load rests on the loose head which does not rotate with the
screw.
The external and internal diameter of the bearing surface of the
loose head...
Question 2 2.1 A brass rod of 25 mm in diameter is enclosed in a steel...
Question 2
2.1 A brass rod of 25 mm in
diameter is enclosed in a steel tube. The tube is 10 mm thick with
an outside diameter of 50 mm. The bar and the tube are initially 1
m long and are rigidly fastened together at each end. Calculate the
stresses in the two materials when the temperature is raised by 80
0C.
2.2 If the composite bar is
then subjected to an axial tensile load of 60 kN, find...
A disk is cast in an open mould with diameter 25 cm and height 15 mm....
A disk is cast in an open mould with diameter 25 cm and height
15 mm. The pouring temperature is 1200°C. Calculate the total heat
evolved during cooling if the disk was cast in copper, and given
that the heat of fusion is 200 kJ/kg.
Question 2 2.1 A brass rod of 25 mm in diameter is enclosed in a steel...
Question 2
2.1 A brass rod of 25 mm in
diameter is enclosed in a steel tube. The tube is 10 mm thick with
an outside diameter of 50 mm. The bar and the tube are initially 1
m long and are rigidly fastened together at each end. Calculate the
stresses in the two materials when the temperature is raised by 80
0C.
2.2 If the composite bar is
then subjected to an axial tensile load of 60 kN, find...
An axial flow fan has a hub diameter of 1.50 m and a tip diameter of...
An axial flow fan has a hub diameter of 1.50 m and a tip
diameter of 2.0 m. It rotates at 18 rad/s and when handling
5.0?^(3)s^(-1) of air, develops a
theoretical head equivalent to 17mm of water. Determine the blade
outlet and inlet angles at the hub and the tip. Assume that the
velocity of flow is independent of radius and that the energy
transfer per unit length of blade is constant. Assume density of
air is1.2 kg/m^3
Ethyl alcohol flows through a horizontal tube having a diameter of 25 mm. If the mean...
Ethyl alcohol flows through a horizontal tube having a diameter
of 25 mm. If the mean velocity is 0.18 m/s, what is the magnitude
of the pressure drop per unit length along the tube (in Pa/m)?
What is the velocity at a distance of 5 mm from the tube axis
(in m/s)?
a .25 mm diameter wire .2 m long is to be held at 1035 deg C....
a .25 mm diameter wire .2 m long is to be held at 1035 deg C.
The wires surface is black. how much electrical power is required
to maintain it's temp? The surrounding air and room are both at 20
deg C. The room is also assumed to be black . Find : Raleigh
number, nusselt number, HTC and power required to maintain
temperature.
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- With the increased use of the Internet, more companies are selling directly to their customers. How...
- If you were developing an advertisement for Huggies diapers; Who would be your target market? What...
- 1) The provided sched.cpp file is missing a few lines to read in some of the data....
- · Describe three major concepts
- Write a module that contains a function sqrt(y, tol=1e-6), which computes a square root of a...
- Fey Fashions expects the following dividend pattern over the next seven years: Year 1 Year 2...
- Discuss how the cognitive theorists (Kelly, Beck, and Ellis) might respond to this question from a...
ADVERTISEMENT