Question

In: Other

An adiabatic dehumidifier is used to extract excess moisture from the air inside your hostel room...

An adiabatic dehumidifier is used to extract excess moisture from the air inside your hostel room with dimension 8 x 6 x 3 m3 . The room was initially at a dry bulb temperature of 30 oC, 70 % relative humidity is to be humidified to 40 % relative humidity. a) Sketch the process in the phsychrometric chart provided b) Estimate the adiabatic saturation temperature of the entrance air and the final temperature (dry bulb) of the air. c) Calculate the amount moisture removed by the humidifier (in kg) d) Briefly explain how could you reduce the humidity further using the humidifier

Solutions

Expert Solution


Related Solutions

A thermometer is taken from an inside room to the outside, where the air temperature is...
A thermometer is taken from an inside room to the outside, where the air temperature is −15° C. After 1 minute the thermometer reads 13° C, and after 5 minutes it reads −1° C. What is the initial temperature of the inside room? (Round your answer to two decimal places.) c = ?
For ethanol liquid with 50% excess of air. Determine adiabatic flame temperature
For ethanol liquid with 50% excess of air. Determine adiabatic flame temperature
9.77 Methane is burned with 25% excess air in a continuous adiabatic reactor. The methane enters...
9.77 Methane is burned with 25% excess air in a continuous adiabatic reactor. The methane enters the reactor at 25 C and 1.10 atm at a rate of 550 L/s, and the entering air is at 150 C and 1.1 atm. Combustion in the reactor is complete, and the reactor effluent gas emerges at 1.05 atm. a) Calculate the temperature and the degrees of superheat of the reactor effluent. (Consider water to be the only condensable species in the effluent)....
Water is boiled in a cup and put to cool down inside a room. The air...
Water is boiled in a cup and put to cool down inside a room. The air temperature in the room is increasing linearly according to the function Ta(t) = 22 + 0.015t (t in minutes, T in Celsius). Assume Newton’s Law of Cooling is satisfied: the rate of change of water temperature is proportional to the difference between the temperature of the water and the temperature of the environment. The temperature of the water was checked after 8 minutes and...
1 – Calculate the adiabatic flame temperature of propane combustion with 50% excess air. 2– Use...
1 – Calculate the adiabatic flame temperature of propane combustion with 50% excess air. 2– Use an online adiabatic flame calculator to calculate the adiabatic flame temperature of propane with air in increments of 0.1 equivalence ratio from 0.5 to 1.2. Plot your results and determine the point that the flame has the maximum T. Compare your results with that of Problem 1.
For ethanol liquid C_5 H_5 O H with 50% excess of air. Determine adiabatic flame temperature
For ethanol liquid C_5 H_5 O H with 50% excess of air. Determine adiabatic flame temperature
Discuss the importance of protecting interior spaces from intrusion of air and moisture. Items of importance...
Discuss the importance of protecting interior spaces from intrusion of air and moisture. Items of importance in your discussion include: Impact to occupants Impact to interior building material Impact to exterior building material as air and moisture moves through the structure
air is compressed in an adiabatic and isentropic compressor from 14 psia and 60F to 210...
air is compressed in an adiabatic and isentropic compressor from 14 psia and 60F to 210 psia. Determine the outlet temperature [F] and the work consumed by this compressor per unit mas of air [Btu/lbm]. Assume constant specific heats at T=100F Please explain table look ups, thank you!
Propane burns with 15% excess air. Before the propane-air mixture enters the burner, air preheats from...
Propane burns with 15% excess air. Before the propane-air mixture enters the burner, air preheats from 32 F to 575 F. Determine the requirements of the preheater (BTU / h) if the amount of propane fed to the burner is 1.35x105 SCFH (standard cubic feet per hour) Note: In this case, take standard conditions in the natural gas industry, such as 60 F and 1 atm. Report: a) Flow diagram of the complete process and its table of material balance...
An engine cycle is used to extract work from a nuclear reactor with helium as the...
An engine cycle is used to extract work from a nuclear reactor with helium as the working fluid. The helium enters a compressor, and its pressure is raised adiabat- ically. It is then heated at constant pressure to a high temperature in the reactor core. The energy is supplied by the fission of plutonium. The helium then enters a turbine, in which it is allowed to expand adiabatically. It then passes through a pre-cooler, in which heat is rejected at...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT