The specifications for a manifold gasket that installs between two engine parts calls for a thickness...

The specifications for a manifold gasket that installs between two engine parts calls for a thickness of 2.500 mm + .020 mm. The standard deviation of the process is estimated to be 0.004 mm.

What are the upper and lower specification limits for this product? The process is currently operating at a mean thickness of 2.50 mm.

(a) What is the Cp for this process?

(b) About what percent of all units of this liner will meet specifications? Does this meet the technical definition of Six Sigma?

Note: Please show step by step calculation

Expert Solution

keosha answered 2 years ago

Assignment Specifications Task Criteria: There are two parts to this assignment. Part 1 – Analysis of...

Assignment Specifications Task Criteria: There are two parts to this assignment. Part 1 – Analysis of Mini Case (must demonstrate understanding of the theories or concepts in the case and their applications. Part 2 – Critical Thinking. Must demonstrate critical thinking skills to develop a valid discussion and with supporting evidence to your chosen product and target markets. Details of task requirements: Part 1: Mini Case (video) Analysis of Market Segmentation, watch “Grilled Burger” ad and answer 2 questions below....

a) The design specifications for a small PVC liner for a construction project calls for a...

a) The design specifications for a small PVC liner for a construction project calls for a thickness of 3.0 mm  0.1 mm. The standard deviation of the process is 0.02 mm. What are the upper and lower specification limits for this product? The process is known to operate at a mean thickness of 3.0 mm. What is the Cpk for this process? Is the process capable of meeting design specification? b) The following jobs are waiting to be...

It is essential in the manufacture of machinery to utilize parts that conform to specifications. In...

It is essential in the manufacture of machinery to utilize parts that conform to specifications. In the past, diameters of the ball-bearings produced by a certain manufacturer had a variance of 0.01 cm. To cut costs, the manufacturer instituted a less expensive production method. The variance of the diameter of 20 randomly samples bearings produced by the new process was 0.015 cm. Use α = 0.05 and assume that the diameters are normally distributed. a) Use hypothesis testing to test...

Consider an engine parts supplier and suppose they determined that the variance of all cylindrical engine...

Consider an engine parts supplier and suppose they determined that the variance of all cylindrical engine parts diameters produced by the current machine is .007. To reduce this variance, a new machine is designed. A random sample from the new machine is taken of 25 parts, which have a variance of .0046. At the 1% significance level, can we conclude that the new machine produces a smaller diameter variance? Please show all work hand written.

MATLAB based problem: Create a motoring model for the engine with the following specifications, and plot...

MATLAB based problem: Create a motoring model for the engine with the following specifications, and plot the in-cylinder pressure against (i) cylinder volume and (ii) crank angle degrees (20 points) Bore = 107mm, stroke = 124mm, compression ratio = 17.3, Length of connecting rod = 192mm. Assume the ratio of specific heats is 1.4 (constant), atmospheric pressure is 1 bar and ambient temperature is 298 K.

THERMODYNAMIC The specifications of a typical reciprocating internal combustion engine coupled with a generator are given...

THERMODYNAMIC The specifications of a typical reciprocating internal combustion engine coupled with a generator are given in Table Q2. With the aid of a P-v diagram, determine the following engine performance characteristics by using constant specific heat at room temperature: i) the total mass contained in the cylinder per cycle, ii) the mass of fuel burned per cycle, iii) the mean effective pressure, iv) the engine power in kW, and v) the specific fuel consumption in g/kWh . Table Q2...

A firm can choose between two production technologies for a new product line. If it installs...

A firm can choose between two production technologies for a new product line. If it installs technology 1, its yearly costs will be: ?1=4500+25?+45?2. If it installs technology 2, its yearly costs will be: ?2=400+125?+?2. What is the marginal and average cost of each technology? What is the minimum efficient scale of both technologies? Which technology would the firm prefer (purely from a cost standpoint) if it expects to sell 60 units each year?

StarPoint manufactures engine parts for Ford using two plants, one in Austin, TX and one in...

StarPoint manufactures engine parts for Ford using two plants, one in Austin, TX and one in Fairfax, VA. The Inverse Demand functions (demand curves) for the two StarPoint plants are: Austin: PA= 30 - 0.125QA Fairfax: PF= 35 - 0.25QF Where QA and QF are outputs of engine parts (in units) from the Austin and Fairfax plants, respectively. The marginal cost of production in Austin (MCA) is 10 and the marginal cost of production in Fairfax (MCF) is 5. If...

A high performance 4 stroke supercharged gasoline engine is being designed. The target specifications are as...

A high performance 4 stroke supercharged gasoline engine is being designed. The target specifications are as follows: IMEP: 25 bar at peak power bsfc: 237 g/kWh isfc: 211 g/kWh Bore to stroke ratio: 1.1 Number of cylinders: 4 Maximum mean piston speed: 21 m/s Compression ratio: 10.5:1 Simulation results indicate that the indicated work per cylinder per cycle needs to be 1550 J/cyl/cyc. Based on the provided information, finalize the engine design for the following parameters: Bore and stroke (mm)...

A thin film of oil (n = 1.4) of thickness 1.4micrometers. is compressed between two glass...

A thin film of oil (n = 1.4) of thickness 1.4micrometers. is compressed between two glass slabs (n = 1.5). White light containing wavelengths from 400 to 700nm (measured in air) is incident normally on the film. In the reflected light, which wavelengths (from long to short)are a) missing (4 of them) and b) enhanced (4 of them)

Question