Question

In: Civil Engineering

A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The...

A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan. The concrete strength at transfer is 22 MPa, and at maturity is 40 MPa. Assume Ec = 32800 MPa, γc = 24 kN/m3 and ignore any prestress losses.

Estimate the approximate total short-term and long-term deflection under the load combination G + 0.7Q. Assume Pi = 1750 kN and Фcc = 2.8.

Solutions

Expert Solution

Ally Wells answered 10 months ago
Next > < Previous

Related Solutions

) A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below....
) A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan....
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan. The...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The...
A 1200 mm deep by 750 mm wide post-tensioned simply supported beam is shown below. The beam spans 12.0 m and is subject to a superimposed dead load of 50 kN/m and a live load of 35 kN/m. Both the superimposed dead load and live load are applied after transfer (after stressing has taken place). The tendon is located at the mid-height of the beam at each end, and its centreline sits 50 mm from the base at midspan. The...
A post-tensioned concrete beam, 170 mm wide and 320 mm deep, is prestressed five wires of...
A post-tensioned concrete beam, 170 mm wide and 320 mm deep, is prestressed five wires of 8 mm diameter located at constant eccentricity of 50 mm and carrying an initial stress of 840 N/mm. The span of the beam is 10 m. Calculate the percentage loss of stress in wires for The beam is pretensioned and The beam is post- tensioned. Using the following data: Es = 210 kN/mm2, Ec = 35 kN/mm, Creep coefficient = 1.6, %3D Relaxation of...
A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports...
A prestressed concrete beam with a rectangular sectin 120 mm wide by 300 mm deep supports a a live load of 3 kN/m. The spanning over 6 m is prestressed by a straight cable carrying an effective prestressing force of 200000 N located at an eccentricity of 55 mm, the density of concrete 24 kN/m3. Find : (1)- The resultant stress distribution for the centre of span cross section of the beam (2)- the presressing force which can balance the...
What is the significance of the simply supported beam bridge and what is the implication simply...
What is the significance of the simply supported beam bridge and what is the implication simply supported beam is applied on the bridge?
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. USING AMM. a.) The maximum deflection is located at what distance from the left support? Answer: 1.63m b.) Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4 Answer 2.9mm
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported...
Consider a concrete beam in an interior environment as follows: a. The beam is simply supported with a design span of 4.8 metres. b. The dead load in the beam is uniformly distributed. c. Dead load on the beam, in addition to its own weight, is 6.9 KN/m of which 75% is permanent (long term). d. The beam carries a single concentrated live load at mid-span of 70 KN. e. 20% of the live load is considered short term. f....
A beam 3m long is simply supported at its ends. The beam is loaded with a...
A beam 3m long is simply supported at its ends. The beam is loaded with a downward vertical load of 200N at a point 2m from the left support. Using DIM: a. The maximum deflection is located at what distance from the left support? b. Calculate the maximum deflection assuming E = 50 GPa and I = 1x10^6 mm4
Consider a simply supported beam of length L. The beam experiences a parabolically varying distributed load...
Consider a simply supported beam of length L. The beam experiences a parabolically varying distributed load that varies from 0 at the left support, to a maximum w at midspan, and back to 0 at the right support. The beam has stiffness properties EI. Give a mathematical equation that gives the value of the distributed load intensity at any distance z along the beam in terms of w, L and z. Draw the SFD and BMD of the beam, giving...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT