Should I use the maximum value for the bending moment in the negative area for compression...

Should I use the maximum value for the bending moment in the negative area for compression stress and maximum bending moment in the positive are for tension stress?

Expert Solution

Solution is attached in the image posted below.

Hope it helps.

If you have any query please comment in the comment box.

A positive response from your side will help me.

Ally Wells answered 11 months ago

What is the formula for maximum deflection and maximum bending moment of a simply support and...

What is the formula for maximum deflection and maximum bending moment of a simply support and cantilever beam that carry a uniformly varying load?

Explain how the positive and negative bending moment in the beam is accounted in the construction...

Explain how the positive and negative bending moment in the beam is accounted in the construction of the beam.

Find the maximum bending moment and locate the point of inflection for a propped cantilever beam...

Find the maximum bending moment and locate the point of inflection for a propped cantilever beam of span 8 m due to a uniformly varying load, whose intensity is 10 kN/m at the fixed support and 2 kN/m at the simple support

How calculation of moment of inertia will influence the bending stress value of a rectangular section?...

How calculation of moment of inertia will influence the bending stress value of a rectangular section? Also find the bending stress for a rectangular section of size 3500 mm X 650 cm in which the bending moment will be taken as 300x103 Nmm.

The magnetic dipole moment (μ) of a coil depends on the current (I), the area of...

The magnetic dipole moment (μ) of a coil depends on the current (I), the area of the coil (A), and the number of loops (N). Rank the three different coils of wire shown figure below in order by the magnitude of their magnetic dipole moment. Rank the coils from greatest to least magnetic dipole moment. If the coils have the same magnetic dipole moment, place them on top of each other.

Please use Excel for calculations: Find out the maximum stress and out unconfined compression strength and...

Please use Excel for calculations: Find out the maximum stress and out unconfined compression strength and cohesion of soil then Draw Mohr Circle (Use graph and drawing compass NOT FREE HAND DRAWING) Diameter= 7.29 cm Height of Sample= 14.78 cm Deformation Dial: 1 unit = 0.10mm; Proving Ring No: 24691; Load Dial: 1 unit = 0.3154 lb Deformation Dial Reading Load Dial Reading 0 0 20 4 40 9 60 12 80 19 100 21 120 24 140 26 160...

How to size an I section under shear bending? Stress calculation should be done at which...

How to size an I section under shear bending? Stress calculation should be done at which points, why? Which of the parameters that affect stress are more critical? What changes when the section is L, rectangular, or U? What additional inspections should be made for a safe design or what principles should be used for the check? How to choose the section or point to be checked? Explain with formulas, figures, and equations.

I want to create an image compression program with matlab use PCA. I have the code...

I want to create an image compression program with matlab use PCA. I have the code listed below. But this code is fail, the image is colorless, but still gray. Can you help me to fix my code. clc clear all picture = im2double(imread('picture1.jpg')); Red = picture(:,:,1); premean = mean(Red(:)); premax = max(Red(:)); premin = min(Red(:)); x = size(Red,1); y = size(Red,2); Z = ones(x,y)*premean; A = (Red - Z)*(1/premax - premin); B = cov(A); [veceig,eig,C] = pcacov(B); NewRed =...

I expect that there will be a negative corellation between age and use of cleaning to...

I expect that there will be a negative corellation between age and use of cleaning to cope with stress, as age goes up use of cleaning to cope with stress will be more likely. explain in a esssay on how this would possiple.

What starting reagent should I use to synthesize chlorocyclohexene? What starting reagent should I use to...

What starting reagent should I use to synthesize chlorocyclohexene? What starting reagent should I use to synthesize 2-chloro-2-methylpropane? The options for starting reagents are 3-methyl-1-butanol, benzyl alcohol, cyclohexanol, and 2-methyl-2-propanol. Alcohol Halogenation Procedure Enter the synthesis lab [left-hand desk]. Click on Alcohol Halogenation on the chalkboard. Decide on the appropriate starting reagent[s] to synthesize chlorocyclohexane. Use ether as solvent. Build the experimental setup. Use a heater, condenser and nitrogen gas. Add the appropriate organic reagents to a flask, and move...

Question