Question

In: Mechanical Engineering

A feedwater heater is a device to heat the feedwater before it goes into the boiler....

A feedwater heater is a device to heat the feedwater before it goes into the boiler. This device receives one stream of saturated vapor at 0.8 MPa and another stream of compressed liquid at 0.8 MPa and 60 oC. These two streams combined to become saturated liquid at 0.8 MPa at the exit of the feedwater heater. The mass flow rate of the compressed liquid is 100 kg/s. Determine a) the mass flow rate of the saturated vapor, b) the exergy destroyed in the feedwater heater (To=300K, Po=0.1 MPa) (10)

Solutions

Expert Solution

H​​​​I sir, please give POSITIVE rating thank you...

samet mamat answered 10 months ago
Next > < Previous

Related Solutions

4. Consider a reheat–regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and...
4. Consider a reheat–regenerative vapor power cycle with two feedwater heaters, a closed feedwater heater and an open feedwater heater. Steam enters the first turbine at 12.0 MPa, 520C and expands to 0.6 MPa. The steam is reheated to 440C before entering the second turbine, where it expands to the condenser pressure of 0.006 MPa. Steam is extracted from the first turbine at 2 MPa and fed to the closed feedwater heater. Feedwater leaves the closed heater at 200C and...
what is firehole furnace, bottom blow down and feedwater pump. parts of a boiler
what is firehole furnace, bottom blow down and feedwater pump. parts of a boiler
In large steam power plants, the feedwater is frequently heated in closed feedwater heaters (basically heat...
In large steam power plants, the feedwater is frequently heated in closed feedwater heaters (basically heat exchangers) by steam extracted from the turbine at some stage. Steam enters the feedwater heater at 1.5 MPa and 250℃ and leaves as saturated liquid at the same pressure. Feed water enters the heater at 2.5 MPa and 60℃ and leaves at 10℃ below the exit temperature of the steam. Neglecting any heat losses from the outer surfaces of the heater, determine (a) the...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stagge at 12 MPa, 560*C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater operating at 1 MPa. The remaining steam expands through the second turbine stage to the condenser pressure of 6 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. The net power output for the...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stage at 12 MPa, 520◦C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater at 1 MPa. The remaining steam expands through the second turbine stage to the condenser pressure of 6 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. For isentropic processes in the turbines and...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stage at 12 MPa, 560°C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater operating at 1 MPa. The remaining steam expands through the second turbine stage to the condenser pressure of 50 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. The net power output for the...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam...
A power plant operates on a regenerative vapor power cycle with one open feedwater heater. Steam enters the first turbine stage at 12 MPa, 560°C and expands to 1 MPa, where some of the steam is extracted and diverted to the open feedwater heater operating at 1 MPa. The remaining steam expands through the second turbine stage to the condenser pressure of 28 kPa. Saturated liquid exits the open feedwater heater at 1 MPa. The net power output for the...
Why might including more than 1 Closed Feedwater Heater increase the efficency of an Ideal Rankine...
Why might including more than 1 Closed Feedwater Heater increase the efficency of an Ideal Rankine Cycle?
A steam power plant with boiler use coal fuel with net heat 4000 kcal/kg and boiler...
A steam power plant with boiler use coal fuel with net heat 4000 kcal/kg and boiler efficiency 90%. If steam utrbine from the power plsnt generate power output 100 MW, at condition vapor enter at 10 MPa, 520oC and condensate to saturated liquid at 0.08 bar. If the isentropic efficiency turbine and pump is 90%, then a) Calculate coal required (ton/hour) b) Calculate netto efficiency of the power plant c) Calculate Net Plant Heat Rate (kCal/kWh)
This is problem 6-12 from El-Wakil’s Powerplant Technology book -- a condensing only feedwater heater uses...
This is problem 6-12 from El-Wakil’s Powerplant Technology book -- a condensing only feedwater heater uses 7/8-in-OD 90-10 copper-nickel tubes. It receives 84,000 lbm/h of 95 percent quality bled steam at 20 psia, and 160,000 lbm/h of drain from the next higher pressure heater at 240°F. 3.9x106 lbm/h of feedwater goes through the heater at 7 ft/s, 2000 psia, and 195°F. The terminal temperature difference is 5°F. Determine the size, length, and number of tubes based on a U-tube design....
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT