Question

In: Electrical Engineering

I want to build a thin flexible rubber sheet, embedded with piezoelectric materials to convert mechanical...

I want to build a thin flexible rubber sheet, embedded with piezoelectric materials to convert mechanical energy into electrical energy.

Can anyone please tell me how i can proceed with this experiment?

or if there is any online supplier where i can buy from?

Expert Solution

step(01):Identify the material.

Silicon oil rubber has been the most commonly used material for piezoelements.

Also we use chloroprene styrene-butadiene , acrylonitrile butadiene and natural rubber .

To impeove peizoelectric performance of rubber we also use filler material.One of such material is MCF whwere magnetic filler is used.

STEP 02:HOW TO MAKE MCF RUBBER

In the MCF rubber technique a colloidal fluid containing spherical Fe₃O₄ particles on the order of 10 nm in size, as well as other metal particles such as Ni, Fe, Cu, etc., on the order of 1 μm. These particles are dispersed in a solvent such as water, kerosene, or silicone oil to compound a magnetic fluid (MF), which is an ordinary intelligent fluid responsive to the magnetic field due to the Fe₃O₄ particles. When a magnetic field is applied, the Fe₃O₄ particles play a bonding role among the metal particles, allowing numerous metal and Fe₃O₄ particles to aggregate.

REFERENCE OF BELOW IMAGE:https://www.ncbi.nlm.nih.gov/pmc/articles/PMC5336029/figure/sensors-17-00346-f002/

THERE ARE THREE TYPE TO MAKE MCF RUBBER AS SHOWN BELOW IN THE FIGURE.

or what you can do See as per your need you have to find ways to set how much preesure exertion should create how much voltage and current and than choose to buy the online rubber sheet which are avaliable on different online platform like amazon ebay etc after this buy peizoelectric sensor and place in between layer of sheet.

or

there are direct online site which gives this for embeded but i can not say about its gaurantee and response please check youself.

http://www.parlux-npdc.com/

https://www.prior.com

http://abarrubber.com

etc

Manojponduru answered 2 years ago

this is my code I want the opposite i want to convert a postfix expression to...

this is my code I want the opposite i want to convert a postfix expression to infix expression #include <iostream> #include <string> #define SIZE 50 using namespace std; // structure to represent a stack struct Stack { char s[SIZE]; int top; }; void push(Stack *st, char c) { st->top++; st->s[st->top] = c; } char pop(Stack *st) { char c = st->s[st->top]; st->top--; //(A+B)*(C+D) return c; } /* function to check whether a character is an operator or not. this function...

We want to build a circut that measure the resistance of the human body and convert...

We want to build a circut that measure the resistance of the human body and convert it to voltage and the circut should have a led that work when the resistance of the body is low. And also we want to use a 741 op-amp And the measured resistance of the body can be represented by a variable resister(the concept of our circuit is to measure galvanic skin response )

I buy used computers and salvage the parts to build "refurbished" computers. I want to build...

I buy used computers and salvage the parts to build "refurbished" computers. I want to build 1000 computers, and have found suppliers of old working computers which have the following components inside, which cost the following, and are available in the following numbers: Source Number of Mother Boards in Computer Number of 4340 Chips in Computer Number of 686 Chips in Computer Number of 500 GB Hard Drives in Computer Cost/ Computer Number Available Yamaha 1 2 1 2 $50...

i want to take a 12vac input voltage and convert it to 20vdc , 12vdc+, 12vdc-,...

i want to take a 12vac input voltage and convert it to 20vdc , 12vdc+, 12vdc-, 5vdc+ How can i do that using a full bridge rectifier, zener diodes, diodes, capacitors. Cannot use a voltage rectifier chip.

i want for an exercise to find the materials for a supsension car system and manufacturing

I want to convert those codes to assembler code // Problem 1 // for loop J=5...

I want to convert those codes to assembler code // Problem 1 // for loop J=5 for(i=1; i<5; i++) { j-- } // Problem 2 // if - then - else i=4 if (i < 5) then j = 3 else j = 2 // Problem 3 //while loop i = 0 j = 0 while(i==0) { j++ if j = 5 then i = j }

1. Tree thin infinite wires carrying currents I go perpendicularly to the paper sheet that they...

1. Tree thin infinite wires carrying currents I go perpendicularly to the paper sheet that they intersect at the points forming a triangle of side a. Two currents go inside the sheet and one goes outside. Calculate the absolute value of the magnetic field created by the currents in the middle of the sides of the triangle.

Hi! How I can convert from xml file to xlsx(excel ) sheet using Aspose.Cells, in C#...

Hi! How I can convert from xml file to xlsx(excel ) sheet using Aspose.Cells, in C# I Try with this code but I need loop , so every element is one row with elements id (name )in column 1, and texten in column 2. Workbook wb = new workbook(); worksheet ws = wb.worksheets[0]; ws.Cells[0,0].putValue("name"); wb.Save(path, "xml_to_exce.xlsxl"); Thanks!

which materials are best for heat exchangers. I want to know everything that heat exchanger depends...

which materials are best for heat exchangers. I want to know everything that heat exchanger depends on like reynolds no., thermal conductivity, friction factor, etc., please explain everything of dependency of heat exchanger.

I want examples about 1. seasonal fluctuation 2. sale trend 3. plant capacity 4. raw materials...

I want examples about 1. seasonal fluctuation 2. sale trend 3. plant capacity 4. raw materials available 5.cost of distribution