Question

In: Electrical Engineering

For a right-sided system specified by the transfer function H(z) = z/(z - 0.5)and an input...

For a right-sided system specified by the transfer function
H(z) = z/(z - 0.5)and an input x[n] = (0.8)n u[n]
find the poles of the response Y[z] and the ROC.
(Hint: Find X(z). H(z) = Y(z)/X(z). Find individual poles’ ROC and then find the common region of convergence)

Solutions

Expert Solution


Related Solutions

A system has the transfer function H(s)=3(s2+7 s)/(s2+8s+4). Draw a Bode plot of the transfer function...
A system has the transfer function H(s)=3(s2+7 s)/(s2+8s+4). Draw a Bode plot of the transfer function and classify it as lowpass, highpass, bandpass, or bandstop. Draw the Direct Form II for this system.
For the system with transfer function H(s)=1/(s-2)(s-1) determine the ROC for stability.
For the system with transfer function H(s)=1/(s-2)(s-1) determine the ROC for stability.
DeMultiplexer (DeMux) takes single input and transfer to output line which specified by select line. Take...
DeMultiplexer (DeMux) takes single input and transfer to output line which specified by select line. Take your seat no and add all the numbers which are written in your seat no that’s form a decimal number. Now convert this decimal no into 8 bit binary no which assume as an input and S0, S1, S2 are select lines. Stepwise show input data transfer to output line. Verify your answer by timing diagram Truth table and Circuit diagram. What are the...
Determine the transfer function H(s)/Q(s) for the liquid-level system shown in Fig. Resistances R1 and R2...
Determine the transfer function H(s)/Q(s) for the liquid-level system shown in Fig. Resistances R1 and R2 are linear. The flow rate from tank 3 is maintained constant at b by means of a pump; i.e., the flow rate from tank 3 is independent of head h. The tanks are noninteracting
For right sided test for proportion, use z-table to find the critical value when alpha =...
For right sided test for proportion, use z-table to find the critical value when alpha = .08 Please explain how to find
Consider the discrete-time LTI system characterized by the following difference equation with input and initial conditions specified
  Consider the discrete-time LTI system characterized by the following difference equation with input and initial conditions specified: y[n] - 2 y[n-1] – 3 y[n-2] = x[n] , with y[0] = -1 and y[1] = 0, x[n] = (-1/2)n u[n-2]. ? Write a MATLAB program to simulate this difference equation. You may try the commands ‘filter’ or ‘filtic’ or create a loop to compute the values recursively. ? Printout and plot the values of the input signal, x[n] and the...
Derive the equation of motion for the system and obtain its transfer function of Controller for...
Derive the equation of motion for the system and obtain its transfer function of Controller for Propeller Driven Pendulum showing the steps .
Give an imaging system, what is the point spread function and optical transfer function useful measures...
Give an imaging system, what is the point spread function and optical transfer function useful measures off?
x[n] is the input of an LTI system with the impulse response of h[n]. x[n] =...
x[n] is the input of an LTI system with the impulse response of h[n]. x[n] = [1, 2, 3] and h[n] = [4, 6]. Use 4-point DFT and IDFT and zero padding of x[n] and h[n] to find the output y[n].
1. Determine the ROC for stability for transfer function H(s) = 1 / (s-2) ( s-1)...
1. Determine the ROC for stability for transfer function H(s) = 1 / (s-2) ( s-1) 2. Determine the ROC for stability for transfer function H(z) = (z-1) / (z+0.1) (z-0.2)
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT