Question

In: Mechanical Engineering

Design a chain drive for a Centrifugal Pump to be driven by a Steam Turbine. The...

Design a chain drive for a Centrifugal Pump to be driven by a Steam Turbine. The input speed will be 1100 RPM, and the desired output speed is 350 RPM. The conveyor requires 20.0 hp. What type of lubrication will be needed?

Solutions

Expert Solution


Related Solutions

In a combined cycle of gas turbine, can a steam turbine drive the same generator driven...
In a combined cycle of gas turbine, can a steam turbine drive the same generator driven by the gas turbine? Or it must drives a separate generator? Also, is there any gas power station that uses a gas other than natural gas? Please give an example. Also, is there a gas power station that uses synthesis gas?
Design a chain drive for a hammer mill to be driven by a hydraulic drive. the...
Design a chain drive for a hammer mill to be driven by a hydraulic drive. the input speed will be 1200 rpm, and the desired output speed is 335 to 340 rpm, the hammer mill requires 75 hp. lubrication type B should be used and the center distance should not exceed 32 in. mechanical engineering design
A simple steam power cycle contains a turbine, condenser, pump and a boiler. If the turbine...
A simple steam power cycle contains a turbine, condenser, pump and a boiler. If the turbine inlet pressure is 14 MPa and 600 °C, and the Condenser Inlet Pressure is 18 kPa, calculate the following: Turbine Inlet Enthalpy (kJ/kg) Condenser Inlet Enthalpy (kJ/kg) Condenser Inlet Temperature (°C) Pump Inlet Enthalpy (kJ/kg) Boiler Inlet Enthalpy (kJ/kg) Boiler Inlet Temperature (°C) Turbine Work Output (kJ/kg) Boiler Heat Addition (kJ/kg) Net Work Output (kJ/kg) Efficiency of the Cycle (%) Work as accurate as...
A simple steam power cycle contains a turbine, condenser, pump and a boiler. If the turbine...
A simple steam power cycle contains a turbine, condenser, pump and a boiler. If the turbine inlet pressure is 14.5 MPa and 550 °C, and the Condenser Inlet Pressure is 19 kPa, calculate the following: Turbine Inlet Enthalpy (kJ/kg) Condenser Inlet Enthalpy (kJ/kg) Condenser Inlet Temperature (°C) Pump Inlet Enthalpy (kJ/kg) Boiler Inlet Enthalpy (kJ/kg) Boiler Inlet Temperature (°C) Turbine Work Output (kJ/kg) Boiler Heat Addition (kJ/kg) Net Work Output (kJ/kg) Efficiency of the Cycle (%) Work as accurate as...
A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250...
A centrifugal pump is driven at 1300 rpm by a 10 hp motor and delivers 250 GPM at 85 Fahrenheit water against 75 ft water head, assuming that the initial pump efficiency is 65 % doesn’t vary appreciably the maximum flow the pump can deliver is most nearly
A centrifugal pump is to be used to pump water from a lake to a storage...
A centrifugal pump is to be used to pump water from a lake to a storage tank which is 165 feet above the surface of the lake. The pumping rate is to be 10 - 35 gal/min at a water temperature of 43°F. The water is used for drinking but will have to undergo filtration and chlorine treatment because there is sediment in the lake. The pump on hand can develop a discharge pressure of 60.0 psig pumping at a...
A model centrifugal pump with impeller diameter 365 mm is tested at its design operating condition....
A model centrifugal pump with impeller diameter 365 mm is tested at its design operating condition. The test gives the following data when pumping water, speed = 870 rev/min head = 18.9 m capacity = 73.7 L/s efficiency = 89%. A geometrically similar pump is to be designed to pump a fluid with relative density 0.78 against a head of 85 m with a flow of 450 L/s. Determine: A) The impeller size? B) The speed? C) The power input...
The following design and operating data were taken for a large industrial centrifugal water pump: Parameter...
The following design and operating data were taken for a large industrial centrifugal water pump: Parameter Design Operating Flow Q (m^3/h) 800 550 Head H (m) 55 24 (after delivery valve) Power P (kW) 160 124 RPM 1485 1485 Required water flow rate varies from 500 m3/h to 700 m3/h. For the pump to deliver 550 m3/h, the flowrate has been reduced by partially closing the delivery valve. Motor efficiency is 93%. a. Calculate the pump operating efficiency (the ratio...
Steam enters a turbine at a rate of 550 kg/hr. The steam enters the turbine at...
Steam enters a turbine at a rate of 550 kg/hr. The steam enters the turbine at 28 atm and 350°C at a linear velocity of 55 m/s. The steam leaves the turbine at a point 3.5 m below the turbine inlet at atmospheric pressure and a velocity of 355 m/s. The turbine delivers shaft work at a rate of 50 kW, and the heat loss from the turbine is estimated to be 2250 kcal/hr. What is the temperature of the...
Design a roller chain drive with the following data. Specify the chain size, the sizes and...
Design a roller chain drive with the following data. Specify the chain size, the sizes and number of teeth in the sprockets, the number of chain pitches, the center distance, and the angle of wrap of the chain for each sprocket. Specify the Tables and Diagrams you use in the solution. Driver type: Hydraulic drive Driven machine: Rock crusher Input speed (rpm): 655 Input power (hp): 120 Nominal output speed (rpm): 200 Number of strands: 4
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT