Question

In: Mechanical Engineering

A worm & worm wheel gear is connected to a motor running at 1000 rpm. Further...

A worm & worm wheel gear is connected to a motor running at 1000 rpm. Further 03 a gear train is formed using worm wheel having 100 teeth and module of 2mm as a driving gear. Gear “A” having 80 teeth is concentric with the worm wheel which in
turn drives gear “B” in a ratio of 1:1. Gear “C” having 60 teeth and “B” are compound gears. Gear “C” is the driving gear for a simple gear train having one idler gear “D” with 40 teeth. Sketch the gear arrangement and determine:
i. Speed of the output gear “E” having 40 teeth.
ii. Center distance between the worm and output shaft if a worm is having single start thread with a diameter of 20 mm and gear “A” & “B” are spur gears having module of 3 mm and all the gears of simple gear train are helical gears having a module of 2 mm.

Solutions

Expert Solution

Please forgive for the calculation mistake and do comment for any short of queries.

Please give thumbs up if you liked my efforts.


Related Solutions

23 hp, dc shunt motor is running at 1000 rpm when the armature voltage is 600...
23 hp, dc shunt motor is running at 1000 rpm when the armature voltage is 600 V. The armature resistance of the motor is 0.8 ohm, and the field resistance is 900 ohm. The efficiency of the motor at full load is 92 %. a) Calculate the value of the resistance of the dynamic braking at full load. The armature current should be limited to 150% of the rated value. b) If the motor operated in regenerative braking at a...
5a. What is a worm gear reducer? 5b. Why is a worm gear extremely quiet and...
5a. What is a worm gear reducer? 5b. Why is a worm gear extremely quiet and able to tolerate substantial loads?
A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the...
A DC shunt motor drives a centrifugal pump at a speed of 1000 rpm when the terminal voltage and line currents are 200 V and 50 A, respectively. Given the armature resistance, Ra = 0.1 ohm and field resistance, Rf =100 ohm. Design a circuit which the speed of the motor can be controlled by using the added resistance method to the armature circuit and the maximum starting current is 120 A. Next, if the added resistance in the designed...
This is for a VF-30 Bonfiglioli worm drive Gearbox 6.1 Housing 6.2 Worm Gear 6.3 Worm...
This is for a VF-30 Bonfiglioli worm drive Gearbox 6.1 Housing 6.2 Worm Gear 6.3 Worm Shaft For each of the MAJOR components (6.1, 6.2 and 6.3) stated only, analyze and identify the manufacturing processes used to make the component – both primary (bulk shape forming) and secondary (or finishing) processes. Include sub-sub-section as follows for each component: o 6.1.1 Component Observations: Describe your observations of the physical component which indicate what manufacturing processes were performed. Include an annotated picture...
15.33 A spur gear reducer has an 18-tooth pinion driven 1500 rpm by an electric motor...
15.33 A spur gear reducer has an 18-tooth pinion driven 1500 rpm by an electric motor and a 36-tooth gear that drives a load involving “moderate shock.” A life of 106 pinion revolutions is required, and the transmitted load, Ft, is 100 lb (this figure includes a safety factor of 2). Conditions are such that Km = 1.8 and kt = 1. It is proposed that standard 20° full-depth gears be used, with both pinion and gear teeth being cut...
How do you calculate the factor of safety for a worm in a worm gear drive?...
How do you calculate the factor of safety for a worm in a worm gear drive? I am looking for the mathematical equations to calculate this. Linking outside resources would be much appreciated.
6. A motor car, of a total mass 1400 kg, running in top gear at 55...
6. A motor car, of a total mass 1400 kg, running in top gear at 55 km/h, passes on to a rsing gradient of 1 in 20 at that speed. The road and other resistances may be taken as constant at 270 N/t. With condition unchanged, the speed falls uniformly to 40 km/h in a distance of 360 m. An intermediate gear is then engaged for which the speed ratio between the engine and the road wheels is 9:1 and...
A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load...
A 6-pole and three-phase induction motor has synchronous speed of (1000) RPM. a) Find the no-load and full-load operating speed of motor for the cases given, 1. 2.5Hz electrical frequency of rotor for no-load condition. 2. 6.3Hz electrical frequency of rotor for full-load condition. b) Find the speed regulation of motor by using parameters found above. c) Determine the electrical frequency of rotor under full-load condition so that speed regulation would be equal to 5%? (Electrical frequency of rotor for...
A wheel rotating at 1800 rpm slows down uniformly to 1200 rpm in 2.0 sec. Calculate:...
A wheel rotating at 1800 rpm slows down uniformly to 1200 rpm in 2.0 sec. Calculate: (a) the angular acceleration (rev/s2) of the motor. (b) the number of revolutions it makes in this time
A Y- connected, 460- V, 1710- rpm, 60- Hz, 4- pole squirrel cage induction motor has...
A Y- connected, 460- V, 1710- rpm, 60- Hz, 4- pole squirrel cage induction motor has a rotor current at starting 6 times the rotor current at full load. Calculate: a. The starting torque as percent of full load torque. b. The slip and speed at which the motor develops maximum torque. c. The maximum torque developed b the motor as percent of its full load value.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT