We know that stress=force/area that is two vectors are divided and we get a tensor but...

We know that stress=force/area that is two vectors are divided and we get a tensor but pressure is also force/area but it is scalar. Why it is so?

Expert Solution

Amanda K answered 2 years ago

Question 1 Stress is defined as 1. Force x Area 2. Force - Area 3. Force...

Question 1 Stress is defined as 1. Force x Area 2. Force - Area 3. Force + Area 4. Force/Area 10 points Question 2 Stress value below the earth surface depends on: 1. Density of soil particles 2. Depth of the point at consideration 3. Both 1 and 2 4. None of the answers 10 points Question 3 Neutral Stress results from: 1. Soil particles 2. Seismic activity 3. Both water and soil 4. Water table 10 points Question 4...

Values of modulus of elasticity (MOE, the ratio of stress, i.e., force per unit area, to...

Values of modulus of elasticity (MOE, the ratio of stress, i.e., force per unit area, to strain, i.e., deformation per unit length, in GPa) and flexural strength (a measure of the ability to resist failure in bending, in MPa) were determined for a sample of concrete beams of a certain type, resulting in the following data: MOE 29.9 33.4 33.6 35.3 35.4 36.2 36.3 36.5 37.7 37.9 38.6 38.8 39.7 41.2 Strength 6.0 7.1 7.3 6.1 8.0 6.6 6.8 7.7...

stress= 2659.588351 psi , force = 522.209 psi/in^2 , area= 0.1963 in^2 , accuracy of load...

stress= 2659.588351 psi , force = 522.209 psi/in^2 , area= 0.1963 in^2 , accuracy of load cell = 0.005 in , accuracy of calliper = 0.001 in , •What is the uncertainty in this stress calculation? Determine which tool (load-cell or calipers) most affects stress calculation *Could you please show all steps because i am going to do it in Excle Thanks in advance

a) Calculate the x- and y-components of the following two force vectors: F1 = 200 Newtons...

a) Calculate the x- and y-components of the following two force vectors: F1 = 200 Newtons @ 30°, F2 = 100 Newtons @ 135° b) What is the magnitude & direction of the resultant vector: R = F1 + F2 3. A football is kicked on a horizontal field at an angle of 40° and a speed of 27 m/sec. a) What are the horizontal & vertical components of the initial velocity? b) Using just your answer for part a,...

A divided multilane highway in a recreational area (fp=0.90) has four lanes (two lanes in each...

A divided multilane highway in a recreational area (fp=0.90) has four lanes (two lanes in each direction) and is on a rolling terrain. The highway has 3 m lanes with a 1.8 m right-side shoulder and a 0.9 m left-side shoulder. The posted speed limit is 80 km/h. Formerly there were 3 access points per km, but recent development has increased the number of access points to 9 access points per km. Before development, the peak-hour factor was 0.90 and...

1.The Vector Product or otherwise know Cross Product of two vectors is itself another vector. When...

1.The Vector Product or otherwise know Cross Product of two vectors is itself another vector. When is the product zero? 2.How does one find the resultant vector of multiple vectors added together? 3.The change in displacement divided by the time interval over which the change in displacement occurs is known as what? 4.The change in velocity divided by the time interval in which the change in velocity occurs is known as what? 5.The constant acceleration of a freely falling object...

If we have two vectors v1 and v2, lie in x-y plane of the Bloch sphere,...

If we have two vectors v1 and v2, lie in x-y plane of the Bloch sphere, then what the angles of phi1 and phi2 should be? and please explain why, thanks.

What is the magnitude of the force per unit area between two infinite, uniformly charged plates...

What is the magnitude of the force per unit area between two infinite, uniformly charged plates with a surface charge density of +4.20

(Steps)Plot a stress-strain curve using Matlab(cross sectional area 30 mm^2) Force (kN) Strain 8.59E-02 0.000054 2.55E-01...

(Steps)Plot a stress-strain curve using Matlab(cross sectional area 30 mm^2) Force (kN) Strain 8.59E-02 0.000054 2.55E-01 0.000054 2.82E-01 0.000054 2.95E-01 0.000054 3.09E-01 0.000054 Step 1:Divide the applied force by the cross-sectional area to be able to get applied stress ?. Also, convert to MPa. 2. Graph the stress-strain curve with strain as the abscissa and stress as the ordinate. 3. Make sure to label the axes with the variable (? or ?) and the correct units. 4. Add a title....

1. We have two potential designs for the homepage of our website, but we don’t know...

1. We have two potential designs for the homepage of our website, but we don’t know which one to use. The CEO likes one, and the CRO (Chief Revenue Office) likes another. Half the company likes one, and the other half of the company likes the other. Which one should we use? 2. Let's say you have an Excel spreadsheet with 10,000 leads from a few months back -- long enough that those leads' sales cycle has passed. The file...

Question