Question

In: Mechanical Engineering

For a bicycle, the nominal diameter of the outer race of a ball bearing and the...

For a bicycle, the nominal diameter of the outer race of a ball bearing and the inner surface of the hub is 62 mm. What should be the maximum dimension for the outer race of the ball bearing if a medium drive hole basis fit is desired? Use a preferred fit.

Solutions

Expert Solution

As medium drive hole basis fit is desired ,the general condition of choosing the type of fit as given below from figurehence Interference fit H7/u6 is being choosen

outer race of bearing acts as hole so the lower limit of outer race will be the nominal size and tolerance will be take from table below for nominal diameter 62 mm

Minimum size= 62mm

Maximum size= 62+0.030=62.030mm


Related Solutions

For a bicycle, the nominal diameter of the outer race of a ball bearing and the...
For a bicycle, the nominal diameter of the outer race of a ball bearing and the inner surface of the hub is 62 mm. What should be the maximum dimension for the hub if a medium drive hole basis fit is desired? Use a preferred fit.
A) To measure the diameter of a ball bearing in a bicycle wheel hub, which of...
A) To measure the diameter of a ball bearing in a bicycle wheel hub, which of the following instruments is most appropriate? a) An electron microscope b) A meter stick c) A graduated cylinder d) Vernier calipers B) A meter stick is balanced on a fulcrum at the 50 cm mark. A student simultaneously suspends a 500 g mass at the 0 cm mark, and a 1 kg mass at the 76 cm mark. What happens next? a) the meter...
For a ball bearing made out of plastic inner and outer race and a stainless steel...
For a ball bearing made out of plastic inner and outer race and a stainless steel ball, which of these materials is likely to wear? What would the wear pattern be like? Which will eventually fail first?
A bearing used in an automotive application is required to have a nominal inside diameter of...
A bearing used in an automotive application is required to have a nominal inside diameter of 1.5 inches. A random sample of 25 bearings is selected and the average inside diameter of these bearings is 1.4975 inches. Bearing diameter is known to be normally distributed with standard deviation 1inch. (a) Test the hypotheses 1.5 versus 1.5 using 0.01 The true mean hole diameter Entry field with correct answer significantly different from 1.5 in. at alpha equals 0.01. (b) What is...
The mean diameter of a ball bearing produced by a certain manufacturer is 0.80 cm with...
The mean diameter of a ball bearing produced by a certain manufacturer is 0.80 cm with a standard deviation of 0.03 cm. A sample of 36 ball bearings is randomly selected from a production run. Suppose the diameter is normally distributed. c. What is the probability that a randomly selected ball bearing will have a diameter of less than 0.798 cm? c. What is the probability that a randomly selected ball bearing will have a diameter of less than 0.798...
A manufacturing company is measuring the diameter of a ball bearing in mm by 12 inspectors,...
A manufacturing company is measuring the diameter of a ball bearing in mm by 12 inspectors, each using two different kinds of calipers to test the difference between the sample means of the two calipers used. Data is shown below. Use excel to resolve. a) Use t-test to check if there is a significant difference between the means of the population of measurements from which the two samples were selected? Use α = 0.01, 0.05, 0.1 and comment on the...
A spherical steel ball bearing has a diameter of 2.540 cm at 29.00°C. (Assume the coefficient...
A spherical steel ball bearing has a diameter of 2.540 cm at 29.00°C. (Assume the coefficient of linear expansion for steel is 11 ✕ 10−6 (°C)−1. ) (a) What is its diameter when its temperature is raised to 96.0°C? (Give your answer to at least four significant figures.) cm (b) What temperature change is required to increase its volume by 0.800%?
The existing record shows machine bearing has a mean diameter of 0.6 inches. Bearing diameter is...
The existing record shows machine bearing has a mean diameter of 0.6 inches. Bearing diameter is known to be normally distributed with standard deviation σ = 0.1 inches. (Additional note: If the mean diameter of bearings is larger or smaller than 0.6 inches, then the process is out of control and must be adjusted.) A random sample of 60 bearings are selected, and the average diameter of the bearing from this sample is 0.55 inches. Use α=0.02 to test the...
A bearing manufacturer wants to determine the inner diameter of a certain grade of bearing. Ideally,...
A bearing manufacturer wants to determine the inner diameter of a certain grade of bearing. Ideally, the diameter would be 15 mm. The data are given in table 2 TIRE NUMBER B1 B2 B3 B4 B5 B6 B7 B8 DIAMETER 14.70 15.10 14.90 14.80 14.89 14.95 14.93 15.05 A. Find the sample mean and median. b. Find the sample variance, standard deviation. c. Analyze the shape of sample data using skewness and kurtosis.
A toroid with inner diameter of 3 cm, outer diameter of 5 cm, and height of...
A toroid with inner diameter of 3 cm, outer diameter of 5 cm, and height of 0.1 cm is made of a body-centered-cubic (bcc) paramagnetic material with lattice parameter equal to 0.5 nm. The toroid is wrapped by a copper wire in 20 turns. If each atom of the magnetic material has a magnetic moment of 1.5µB (Bohr Magneton), (a) (1.5 pt) What is the saturation magnetization (in A/m) of the material? (b) (1.5 pt) If a current of 2...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT