Question

In: Mechanical Engineering

Determine the changes in length, breadth, and thickess of a steel bar which is 5m long,...

Determine the changes in length, breadth, and thickess of a steel bar which is 5m long, 40mm wide and 30mm thick and is subjected to an axial pull of 35kN in the direction of its length. Then find the volumetric strain and final volume of the given steel bar. (Take E= 200000 N/mm2 and poisson ratio (v) = 0.32)

Solutions

Expert Solution


Related Solutions

A steel bar (mass 762 kg, length 88.3 m) is supported by a horizontal wire attached...
A steel bar (mass 762 kg, length 88.3 m) is supported by a horizontal wire attached to a wall. The wire is tied to the beam distance 28.96 m from the top end. The center of mass of the bar is 23.5 m from the bottom. The bar is held at the bottom by a hinge, and makes an angle θ = 46.5o with the horizontal. Find Fhinge, the magnitude of the force exerted by the hinge on the bar,...
A 2.00 m long uniform steel bar rests on the ground and against the wall. Both...
A 2.00 m long uniform steel bar rests on the ground and against the wall. Both the wall and the ground are frictionless. THe steel bar makes an angle of 50 degrees with the ground. To keep the steel bar in static equilibrium, a horizontal wite attaches the steel bar at 0.500m from the bottom to the wall. The mass of the steel bar is 60kg. a) Draw a free body diagram showing all the forces on the steel bar...
Determine the required size (area, nominal diameter, and Bar No.) of the three reinforcing steel bars...
Determine the required size (area, nominal diameter, and Bar No.) of the three reinforcing steel bars used in a 9 in. wide and 12 in. deep concrete beam to assure the beam fails in compression of the concrete and the steel reinforcement reaches its yield strength at the same load. Assume that the ultimate compressive strength of the concrete is 4,000 psi and the yield strength of the steel is 30,000 psi.
Compare and contrast the Fundamental with the Realized Niche. How will niche breadth respond to changes...
Compare and contrast the Fundamental with the Realized Niche. How will niche breadth respond to changes in competitors and resource availability?
Determine the Average Run Length (ARL) of a x-bar chart with limits where the process has...
Determine the Average Run Length (ARL) of a x-bar chart with limits where the process has shifted one standard deviation in one direction
A steel shaft is to be manufactured either as a solid circular bar or as a...
A steel shaft is to be manufactured either as a solid circular bar or as a circular tube. The shaft is required to transmit a torque of 1200 N_m without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of0.75°/m. (The shear modulus of elasticity of the steel is 78 GPa.). Determine the required outer diameter do of the solid shaft [58.8 mm] Determine the required diameter d2of the hollow shaft if thethickness t of...
A ladder of mass 30 kg and length 5m leans against a frictionless wall. The angle...
A ladder of mass 30 kg and length 5m leans against a frictionless wall. The angle between the ladder and the wall is 37 degree. (a) what is the force between the ladder and the wall? (b) a 60 kg man now climbs up to the midpoint of the ladder, what is the force at the base of the ladder (magnitude and direction).? (c) what must be the coefficient of friction so that the mass can climb all the way...
Integrative-long dashRisk and Valuation: Hamlin Steel Company wishes to determine the value of Craft​ Foundry, a...
Integrative-long dashRisk and Valuation: Hamlin Steel Company wishes to determine the value of Craft​ Foundry, a firm that it is considering acquiring for cash. Hamlin wishes to determine the applicable discount rate to use as an input to the​ constant-growth valuation model. ​ Craft's stock is not publicly traded. After studying the required returns of firms similar to Craft that are publicly​ traded, Hamlin believes that an appropriate risk premium on Craft stock is about 9​%. The​ risk-free rate is...
Suppose a batch of steel rods produced at a steel plant have a mean length of...
Suppose a batch of steel rods produced at a steel plant have a mean length of 151 millimeters, and a variance of 64. If 116 rods are sampled at random from the batch, what is the probability that the length of the sample rods would differ from the population mean by more than 0.81 millimeters? Round your answer to four decimal places.
Suppose a batch of steel rods produced at a steel plant have a mean length of...
Suppose a batch of steel rods produced at a steel plant have a mean length of 151 millimeters, and a variance of 64. If 116 rods are sampled at random from the batch, what is the probability that the length of the sample rods would differ from the population mean by more than 0.81 millimeters? Round your answer to four decimal places.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT