A solid cylinder of 6 inch diameter and 4 inch high is compressed axisymmetrically to 2...

A solid cylinder of 6 inch diameter and 4 inch high is compressed axisymmetrically to 2 inch high.
a) Calculate the final diameter of the product, the three orthogonal strains and the Von Mises strain.
b) Estimate the maximum total force required for this operation. Assume: coefficient of fricition 0.2; Use Ludwik's Law to find the pressure at maximum axial strain; the strength coefficient of the workpiece: K is 147 ksi, strain hardening exponent is 0.17.

Expert Solution

samet mamat answered 3 years ago

a. If a 6 cm diameter cylinder containing 2 g of an ideal gas at 25o...

a. If a 6 cm diameter cylinder containing 2 g of an ideal gas at 25o C is fitted with a 5 kg piston with a 20 kg weight on the piston, calculate the pressure and volume of the ideal gas if the atmospheric pressure is 1 atm. If the 20 kg weight is removed, provide detailed comments without further calculations on what would happen. You may assume a molecular weight of 28 for the gas. b. Calculate the energy...

Define the system, control volume, and control surface for a 4-foot, 6-inch diameter section of pipe....

Define the system, control volume, and control surface for a 4-foot, 6-inch diameter section of pipe. Is the system Lagrangian or Eulerian? Why?

A cylinder with a 20 inch stroke and a 4:3 area ratio with a bore of...

A cylinder with a 20 inch stroke and a 4:3 area ratio with a bore of 6 inch diameter takes 4 seconds to extend. What is the flow required for extention?

A solid cylinder of diameter 5m has a Hight of 4m Find the metacentric height of...

A solid cylinder of diameter 5m has a Hight of 4m Find the metacentric height of the cylinder. If the specific gravity of the material of the cylinder is 0.7 and is floating in the water with its axis vertical. State whether the equilibrium is stable or unstable.

A uniform brass solid cylinder has a mass, m = 500 g, and a diameter, D...

A uniform brass solid cylinder has a mass, m = 500 g, and a diameter, D = 6 cm and a length L = 1 m. The cylinder rotates about its axis of rotational symmetry at an angular velocity of 60 radians/s on a frictionless bearing. (a) What is the angular momentum of the cylinder? (b) How much work was required to increase the angular momentum of the cylinder to this value if the cylinder was initially at rest? Once...

A solid, uniform cylinder with mass 8.25 kg and diameter 10.0 cm is spinning with angular...

A solid, uniform cylinder with mass 8.25 kg and diameter 10.0 cm is spinning with angular velocity 245 rpm on a thin, frictionless axle that passes along the cylinder axis. You design a simple friction-brake to stop the cylinder by pressing the brake against the outer rim with a normal force. The coefficient of kinetic friction between the brake and rim is 0.344.

cooling a gas in a piston cylinder. if the boundary work of piston cylinder is compressed...

cooling a gas in a piston cylinder. if the boundary work of piston cylinder is compressed W = -10 kj determine if it is gained or lost by the gas.

A vertical cylinder 76.2mm in diameter and 121.9mm high is maintained at 397.1K at its surface....

A vertical cylinder 76.2mm in diameter and 121.9mm high is maintained at 397.1K at its surface. It loses heat by natural convection to air at 294.3K. Heat is lost from the cylindrical side and the flat circular end at the top. Calculate the heat loss, neglecting radiation losses. Use the simplified equations of Table 1.5-2 and those equations for the lowest range of GrPr. The equivalent L use the top flat surface is 0.9 times the diameter

You have a nominal 3-inch diameter steel pipe, 15 feet high that is embedded into a...

You have a nominal 3-inch diameter steel pipe, 15 feet high that is embedded into a concrete foundation. Neglecting the weight of the column, answer the questions below: A. What is the maximum vertical load this pipe can support/critical load (#)? B. If a vertical load of 2,000#s and a horizontal force of 100#s are applied at the top of the column, what are the maximum combined tensile and compressive stresses (psi) where the column meets its foundation? Are they...

A 5-m-long cylinder of solid aluminum has a radius of 2 cm. (a) If the cylinder...

A 5-m-long cylinder of solid aluminum has a radius of 2 cm. (a) If the cylinder is at a temperature of 0 °C, how much will the length change when the temperature rises to 50 °C? m (b) Due to the temperature increase, by how much would the density of the aluminum cylinder change? The density decreases by % upon heating. (c) By what percentage does the volume of the cylinder increase? The volume increases by % upon heating.

Question