Question

In: Mechanical Engineering

A long cylindrical object with diameter D=100cm (k=400 W/mK, C­p = 400 J/kg K, density =...

A long cylindrical object with diameter D=100cm (k=400 W/mK, C­p = 400 J/kg K, density = 9000 kg/m3) is put into an oven of 1100 K with convective

heat transfer coefficient h of 50 W/m2 K. The initial temperature of this object is 300 K. How much time does it take for the center of the object to reach

700K? How much time does it take for the surface of the object to reach 700K?

Solutions

Expert Solution


Related Solutions

A nuclear fuel element is in the form of long solid cylindrical rod (k=0.85 W/mK) of...
A nuclear fuel element is in the form of long solid cylindrical rod (k=0.85 W/mK) of diameter 14 mm is generating heat at an uniform rate of 0.45×108 W/m3 because of nuclear fission. Heat is transfer to pressurized cooling water at 300 0C and surface heat transfer coefficient is 4500 W/m2k. calculate the maximum temperature in the fuel rod in the system. What is the change in Tmax if the fuel element is encapsulated in a thin metal cladding of...
A 400-W cylindrical resistance heater is 1 m long and 0.5-cm-diameter. The resistance wire is placed...
A 400-W cylindrical resistance heater is 1 m long and 0.5-cm-diameter. The resistance wire is placed horizontally in a fluid at 20◦C, flowing at a velocity of 20 m/s. Determine the outer surface temperature of the resistance wire in steady operation if the fluid is (a) air and (b) water. Ignore any heat transfer by radiation and evaluate properties of air at 800 K and properties of water at 315 K.
The circular fin of diameter D=1mm and length L=25.4mm, made of copper (k=400 W/m.K), are used...
The circular fin of diameter D=1mm and length L=25.4mm, made of copper (k=400 W/m.K), are used to enhance heat transfer from a surface that is maintained at temperature Tb=132 °C. and the rod has another end attached to a large surface which is maintained at Te= 0°C. The airflow through the rod surfaces is at T∞ = 0 °C with convection heat transfer coefficient h = 100 W/m2.K. (Hint: use table 3.4 in the lecture slides.) (a) Express temperature T(x)...
A composite cylindrical wall is composed of 2 materials of thermal conductivity ka = 240 W/mK...
A composite cylindrical wall is composed of 2 materials of thermal conductivity ka = 240 W/mK and kb = 20 W/mK, where interfacial contact resistance is negligible. - Liquid pumped through the tube is at a temperature Tinf, i = 200 F and provides a convection coefficient hi = 450 W/m^2K at the inner surface of the composite pipe -The outer surface is exposed to Tinf, o and provides a convection coefficient of ho = 20 W/m^2K -A thermocouple between...
FIreclay brick (ρ=2050 kg/m3, cp=960 J/kg-K, k=1.1 W/m-K) with dimensions 0.06 m x 0.09 m x...
FIreclay brick (ρ=2050 kg/m3, cp=960 J/kg-K, k=1.1 W/m-K) with dimensions 0.06 m x 0.09 m x 0.20 m is removed from a kiln at 1600K and cooled in air at 40C with h = 30 W/m2-K. What is the temperature at the corner of the brick after 50 minutes of cooling? Give your answer in degrees C.
A packed bed of uniform spherical particles of diameter, d= 2.5 mm, density ρs= 4000 kg/m3...
A packed bed of uniform spherical particles of diameter, d= 2.5 mm, density ρs= 4000 kg/m3 , and voidage e= 0.45 is fluidised by means of a liquid of viscosity μ= 1 mN s/m2 and density ρ= 900 kg/m3 . (a) Starting from Carman’s and Ergun’s equations reported in the attached equations sheet, derive the corresponding expressions for the minimum fluidising velocity, umf, for both equations and explain their meaning.
cylindrical container with circular hole at the bottom with diameter d , is filled with water...
cylindrical container with circular hole at the bottom with diameter d , is filled with water to height h . Which of the following statement is correct for the itime required to empty the container If d is constant , the time is inversely proportional to the height of water . If h is constant , the time is inversely proportional to the area of hole . If his constant , the time is directly proportional to the area of...
A 8.6-kg cube of copper (cCu = 386 J/kg-K) has a temperature of 750 K. It...
A 8.6-kg cube of copper (cCu = 386 J/kg-K) has a temperature of 750 K. It is dropped into a bucket containing 5.1 kg of water (cwater = 4186 J/kg-K) with an initial temperature of 293 K. 1) What is the final temperature of the water-and-cube system? K 2) If the temperature of the copper was instead 1350 K, it would cause the water to boil. How much liquid water (latent heat of vaporization = 2.26 × 106 J/kg) will...
A thick steel slab (ρ= 7800 kg/m3, c= 480 J/kg·K, k= 50 W/m·K) is initially at...
A thick steel slab (ρ= 7800 kg/m3, c= 480 J/kg·K, k= 50 W/m·K) is initially at 300°C and is cooled by water jets impinging on one of its surfaces. The temperature of the water is 25°C, and the jets maintain an extremely large, approximately uniform convection coefficient at the surface. Assuming that the surface is maintained at the temperature of the water throughout the cooling, how long will it take for the temperature to reach 50°C at a distance of...
A 1-mm diameter sphere (density=7900 kg/m3) is dropped into a tank of oil (density=900 kg/m3). The...
A 1-mm diameter sphere (density=7900 kg/m3) is dropped into a tank of oil (density=900 kg/m3). The sphere develops a terminal speed of 0.25 cm/s, what is the oil's viscosity? You may assume a small Reynolds number. Show your work.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT