A 24-tooth spur gear is to drive a 12-tooth spur gear. For both gears, the diametral pitch is 24 tooth/in.

A 24-tooth spur gear is to drive a 12-tooth spur gear. For both gears, the diametral pitch is 24 tooth/in. The gears are cut on the 20° full-depth involute system. Find and tabulate the addendum, dedendum, clearance, circular pitch, base pitch, tooth thickness at the pitch circle, pitch diameters, base circle radii, and contact ratio.

Expert Solution

samet mamat answered 2 years ago

A 50-tooth spur gear is in mesh with a 27-tooth pinion. The gears have a diametral...

A 50-tooth spur gear is in mesh with a 27-tooth pinion. The gears have a diametral pitch of 5 teeth/in, and a pressure angle of φ = 25°. The gears transmit 80 HP at 4000 pinion rpm. Find the factors of safety against bending and surface failure. Assume that the teeth are full depth, Qv = 10, a through hardened to 360 HB steel gear, and a carburized and case hardened steel pinion. Assume a face width of 3.0 in,...

15.33 A spur gear reducer has an 18-tooth pinion driven 1500 rpm by an electric motor...

15.33 A spur gear reducer has an 18-tooth pinion driven 1500 rpm by an electric motor and a 36-tooth gear that drives a load involving “moderate shock.” A life of 106 pinion revolutions is required, and the transmitted load, Ft, is 100 lb (this figure includes a safety factor of 2). Conditions are such that Km = 1.8 and kt = 1. It is proposed that standard 20° full-depth gears be used, with both pinion and gear teeth being cut...

Question One A quality department is planning to inspect a shipment of 120 spur-gears. The quality...

Question One A quality department is planning to inspect a shipment of 120 spur-gears. The quality engineer has decided to use a sample size of 10 products. If the number of nonconforming products in the shipment is expected to be seven products, help in finding the below: (a) The number of samples contains a maximum of two nonconforming products. (b) The number of samples contains a minimum of four conforming products. (c) The number of samples contains ten conforming products

create a tool for detailed design and stress analysis of Spur Gears. Your tool can be...

create a tool for detailed design and stress analysis of Spur Gears. Your tool can be based on one oft he following or a combination of any:, Matlab, Excel Spreadsheets, KISS soft software, Python,etc. and it can be supported by any FEA and/or CAD software .Use your developed tool to solve a full design problem of your choice.

A power train application requires the coupling of a spur gear to a transmission shaft operating...

A power train application requires the coupling of a spur gear to a transmission shaft operating at 3600RPM. The coupling must sustain a mean torque loading of 215Nm. There is a 20% torque ripple introduced to the drive line from the load. Select and design a coupling system using either a keyed coupling or an interference coupling such that the section of the transmission shaft at that location is minimized. Assume that the gear is located at the midpoint of...

A stock steel spur pinion has a diametral pitch of pd=8 teeth/in, a 1.5 in. face,...

A stock steel spur pinion has a diametral pitch of pd=8 teeth/in, a 1.5 in. face, 26 full-depth teeth, and a pressure angle of Φ = 20°. If the pinion is driven against a 55-tooth steel gear at 1200 RPM by a 7 hp electric motor, determine the bending stresses and surface stresses in the pinion.

What is diametral pitch, and why is it an important parameter in a gear mesh?

Two suppliers manufacture a plastic gear used in a laser printer. The impact of these gears...

Two suppliers manufacture a plastic gear used in a laser printer. The impact of these gears measured in foot-pounds is an important characteristic. Assume the impact strength are normally distributed. A random sample of 10 gears from supplier 1 results in = 289.3 and = 22.5. Another sample of 16 gears from supplier 2 result in = 321.5 and = 21. It is claimed that supplier 2 provide gears with higher mean impact strength. Perform the hypothesis test at significance...

: For your selected gears, determine the following: center distance, pitch circle diameter, outer diameter (or...

: For your selected gears, determine the following: center distance, pitch circle diameter, outer diameter (or addendum diameter), dedendum diameter, base circle diameter, circular pitch, tooth thickness, addendum, dedendum, clearance, whole depth.

Compare the following: belt drive, chain drive, and gear system. What are the fundamental characteristics of...

Compare the following: belt drive, chain drive, and gear system. What are the fundamental characteristics of each? What are the advantages and disadvantages of each?

Question