A horizontal shaft of 75mm diameter projects from a bearing and, in addition to the torque...

A horizontal shaft of 75mm diameter projects from a bearing and, in addition to the torque transmitted, the shaft carries a vertical load of 8 kN at 300 mm from the bearing. If the safe stress for the material, as determined in a simple tension test, is 135 MN/m2 find the safe torque to which the shaft may be subjected using as a criterion
(a) The maximum shearing, stress,
(b) The maximum strain energy per unit volume.
Poisson’s ratio ? = 0.29.

Expert Solution

samet mamat answered 2 years ago

how to calculate a shaft diameter of horizontal wind turbine

A circular shaft, 100 mm diameter is subjected to combined bending moment and torque, the bending...

A circular shaft, 100 mm diameter is subjected to combined bending moment and torque, the bending moment being 3 times the torque. If the direct tension yield point of the material is 300 MN/m2 and the factor of safety on yield is to be 4, calculate the allowable twisting moment by the three following theories of failure: (a) Maximum principal stress theory (b) Maximum shear stress theory (c) Maximum shear strain energy theory.

all journal bearing has a shaft diameter=1.25in and suppports a load of 1200lbf. the bushing is...

all journal bearing has a shaft diameter=1.25in and suppports a load of 1200lbf. the bushing is 1.25-in long and has a bore diameter=1.25in. shfat speed=1500 rev/min. average film temperature=115.4oF and SAE grade 30 lubricant is used. average clearance =0.001125 in. Find a) magnitud and location of min oil-film thickness b) total lubricant volumetric flow rate c) max oil-folm pressure and its angular location d) power loss

For a marine diesel engine application, a fluid-film journal bearing has a shaft diameter of 32...

For a marine diesel engine application, a fluid-film journal bearing has a shaft diameter of 32 mm and the length of the bearing is 24 mm. The bearing uses SAE grade 20 oil as lubricant and operates under a radial load. The inlet and outlet temperatures of oil are 50oC and 110oC respectively. It is assumed that because of the shearing action there is a uniformly distributed energy release in the lubricant that heats the lubricant film. During run-in operation,...

True or False: 1. Keys are used to enable transmission of torque from the shaft to...

True or False: 1. Keys are used to enable transmission of torque from the shaft to the shaft supported elements. 2. For the same bore diameter, a cylindrical roller bearing generally has a lower load carrying capacity than ball bearings. 3. Thrust bearings are suitable for supporting both axial and radial loads. 4. Typical bearing failures are due to excessive static stresses. 5. According to the seminar presentations, materials for joint replacements are selected on basis of the loading as...

A 100mm shaft is loaded with a torque of 100Nm and a bending moment of 50Nm....

A 100mm shaft is loaded with a torque of 100Nm and a bending moment of 50Nm. As a designer you need to select a material to find a suitable material for size, weight and cost. Using Von-Mises stress and the distortion energy failure theory determine the sizing / weight and cost for each of the three materials below. Complete the table with your answers and show all work. Yield Strength Density (kg/m^3) Cost ($/kg) Required Diameter (mm) Weight (kg) Cost...

A journal and bearing are to be designed for a shaft that turns at 250 rpm....

A journal and bearing are to be designed for a shaft that turns at 250 rpm. Suppose ISO VG100 (SAE Engine 30) is to be used as lubricant and the bearing length is to be equal to 1.2 times the diameter. If the no-load power loss is not to exceed 2.5 x 10-4 horsepower and the diametral clearance is 0.0045 times the diameter, estimate the maximum diameter that can be used for the journal, and the allowable temperature limit.

The existing record shows machine bearing has a mean diameter of 0.6 inches. Bearing diameter is...

The existing record shows machine bearing has a mean diameter of 0.6 inches. Bearing diameter is known to be normally distributed with standard deviation σ = 0.1 inches. (Additional note: If the mean diameter of bearings is larger or smaller than 0.6 inches, then the process is out of control and must be adjusted.) A random sample of 60 bearings are selected, and the average diameter of the bearing from this sample is 0.55 inches. Use α=0.02 to test the...

5. A shaft rotates at a rate of 50 RPM against a constant torque of 2000...

5. A shaft rotates at a rate of 50 RPM against a constant torque of 2000 N.m. Calculate: a. The power required to rotate the shaft. b. The work required to rotate the shaft through 150 revolutions.

A shaft inside the sleeve of a journal bearing is being rotated at 1500 rpm. The...

A shaft inside the sleeve of a journal bearing is being rotated at 1500 rpm. The shaft is 6.00 cm in diameter and is rotating in a bearing sleeve that is 6.02 cm in diameter and 40 cm long. The clearance is filled with oil having properties of ?=0.003 m2 /s and SG=0.88. a. Find the torque required to rotate the shaft. b. Find the power required to rotate the shaft. (Answer: 44.1 kW) c. Discussion: How do the torque...

Question