Question

In: Mechanical Engineering

Calculate the heat-removal factor for a collector having an overall heat loss coefficient of 10 W/m2...

Calculate the heat-removal factor for a collector having an overall heat loss coefficient of 10 W/m2 K and constructed of copper fins and tubes (k = 390 W/m?K). Tube-to-tube center distance is 12 cm, fin thickness is 0.05 cm, tube diameter is 1.5 cm, and fluid-tube heat transfer coefficient is 1000 W/m2K. The cover transmittance to solar radiation is 0.8 and is independent of direction. The solar absorptance of the absorber plate is 0.9, the collector is 1 m wide and 2 m long, and the water flow rate is 0.03 kg/s. The water temperature is 330 K.

Solutions

Expert Solution


Related Solutions

Calculate an overall heat loss coefficient for a plate at 50℃, facing up, when exposed to an ambient temperature of 10℃.
Calculate an overall heat loss coefficient for a plate at 50℃, facing up, when exposed to an ambient temperature of 10℃. The plate emittance is 0.88, the dew point is 3℃, and the wind heat transfer coefficient is 25 W/m2℃. Assume time is midnight
Estimate the top heat loss coefficient of a collector that has the following specifications: Collector area=...
Estimate the top heat loss coefficient of a collector that has the following specifications: Collector area= 2m2 Collector slope =35⁰ Number of glass covers = 3 Thickness of each glass cover =4 mm. Thickness of absorbing plate =0.5 mm. Space between glass covers = 20 mm. Space between inner glass cover and absorber =40 mm. Mean absorber temperature, Tp =80 ⁰C Ambient air temperature =15 ⁰C Absorber plate emissivity, εp =0.10. Glass emissivity, εg =0.88 Wind velocity = 2.5m/s. Assuming...
Calculate the heat flux (W / m2) through a composite wall made of material A whose...
Calculate the heat flux (W / m2) through a composite wall made of material A whose k = 40 W / m-K and has a thickness of 30 cm, a material B whose k = 0.05 W / m-K and a thickness of 3 cm; and a material C whose k = 0.004 W / m-K, its thickness is 0.5 cm.
A two-pass shell and tube heat exchanger has an overall conductance of 450 W/m2 oC when...
A two-pass shell and tube heat exchanger has an overall conductance of 450 W/m2 oC when used as a condenser for a large air conditioning system. Refrigerant R-134a enters thecondenser at 20 kg/ s as a saturated vapor at 70oC and leaves as a saturated liquid. If cooling water enters at a rate of 60 L/s, 10oC, determine the outlet temperature of the cooling water and the effective area of the condenser.
Determine the overall heat transfer coefficient (U) in a heat exchanger that uses steam to heat water to the point of vaporization (in vacuum.)
Determine the overall heat transfer coefficient (U) in a heat exchanger that uses steam to heat water to the point of vaporization (in vacuum.) The system is non-insulated, so the heat lost to the surroundings must be taken into consideration. While I know that the heat Q = mCdT and the heat transfer rate q = UAdT(Log-mean), I am struggling to equate the two due to the heat lost to the surroundings. How do I go about determining the overall...
Laser light is polarized and has an intensity of 10 W/m2. A polarizer is placed in...
Laser light is polarized and has an intensity of 10 W/m2. A polarizer is placed in the path of the laser. The intensity is measured again at 5 W/m2. What is the angle of the polarizer with respect to the initial polarization? A. 15 deg B. 20 deg C. 30 deg D. 45 deg
The heat transfer coefficient of a steel (k = 43 W/m · K) tube (1.9 cm...
The heat transfer coefficient of a steel (k = 43 W/m · K) tube (1.9 cm ID and 2.3 cm OD) in a shell-and-tube heat exchanger is 500 W/m2 · K on the inside and 120 W/m2 · K on the shell side, and it has a deposit with a total fouling factor of 0.000176 m2 · K/W. Calculate a. The overall heat transfer coefficient b. The cleanliness factor, and percent over surface.
The diffusion coefficient of a large protein molecule is found to be 2.2×10-13 m2/s in the...
The diffusion coefficient of a large protein molecule is found to be 2.2×10-13 m2/s in the water at 20∘C. Assuming it is spherical with a density of 1.3×103 kg/m3, compute its molar mass.
A beam of x-ray is incident on bone at an intensity of 10 W/m2. Make plot...
A beam of x-ray is incident on bone at an intensity of 10 W/m2. Make plot with your graphics calculator of the intensity as a function of distance through the tissue for energy levels corresponding to : 200 kV, 100 kV, and 50 kV. Draw all curves on the same axis. Repeat this exercise for muscle tissue and compare the results
Light of wavelength 400 nm and intensity 10^-2 W/m2 is incident on potassium. (a) Estimate the...
Light of wavelength 400 nm and intensity 10^-2 W/m2 is incident on potassium. (a) Estimate the time lag for the emission of photoelectrons expected classically. Assume the typical radius of an atom is 10 ^-10 m. Hint: Relate the light intensity to the work function for potassium. (b) How many photons are incident per second per square meter
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT