The amount of warpage in a type of wafer used in the manufacture of integrated circuits...

The amount of warpage in a type of wafer used in the manufacture of integrated circuits has a mean of 1.3 mm and a standard deviation of 0.1 mm. A random sample of 200 wafers is drawn.

A)What is the probability that the sample mean warpage exceeds 1.305 mm?

B)How many wafers must be sampled so that the probability is 0.05 that the sample mean exceeds 1.305?

C)What is the probability that the sample total warpage exceeds 200 mm?

D)Let be the sample mean. If P( > x) = .9357, find x.

Solutions

Expert Solution

orchestra answered 1 year ago

Next > < Previous

Related Solutions

Mention two uses for the current sources in analog integrated circuits?

What type Integrated Circuit do I need to light a certain amount of connected series or...

What type Integrated Circuit do I need to light a certain amount of connected series or parallel LEDS depending on my voltage. So I have a system that harvest energy and charging a capacitor steadily to around 3V max and I want it to make it so as it's charging the LED lights up. Let say 0.5V LED1 light up and at max voltage all LED light up, so up to say 5 LEDS. Is this possible? if it is...

A manufacturer of integrated circuits is planning production for the next four months. The forecast demand...

A manufacturer of integrated circuits is planning production for the next four months. The forecast demand for the circuits is shown in the following table. Circuit September October November December IC341 650 875 790 1100 IC256 900 350 1200 1300 At the beginning of September, the warehouse is expected to be completely empty. There is room for no more than 1,800 integrated circuits to be stored. Holding costs for both types is $0.05 per unit per month. Because workers are...

A company is manufacturing integrated circuits. The design specifies the nominal thickness of the IC resistance...

A company is manufacturing integrated circuits. The design specifies the nominal thickness of the IC resistance layer to be 100 units. If the thickness strays too far from 100 units IC performance may be degraded. Assume the process is in control when 25 samples of IC resistance layer thickness (each of size 4) were taken off the production line. Using the methods of Control Charts for Variables, we want to achieve statistical control of the resistance layer thickness using X-bar...

Manufacturing integrated circuits is an enormously complicated task, as there are many process variables that can...

Manufacturing integrated circuits is an enormously complicated task, as there are many process variables that can be manipulated (thickness of this, width of that, doping level of something else, etc). Generally speaking, many copies of a circuit are put onto a single wafer, which is made all at once. We have an experiment where we are varying two factors, each at two levels. We have 20 wafers and assign each of the four factor/level combinations to five wafers at random...

The fraction of defective integrated circuits produced in a photolithography process is being studied. A random...

The fraction of defective integrated circuits produced in a photolithography process is being studied. A random sample of 300 circuits is tested, revealing 15 defectives. (a) Calculate a 95% two-sided confidence interval on the fraction of defective circuits produced by this particular tool. Round the answers to 4 decimal places. Entry field with incorrect answer now contains modified data less-than-or-equal-to p less-than-or-equal-to Entry field with incorrect answer now contains modified data (b) Calculate a 95% upper confidence bound on the...

The single most important use of the element gold is for wires that join integrated circuits...

The single most important use of the element gold is for wires that join integrated circuits to the conducting pads that then connect microelectronic chips with external circuitry. A typical application uses gold wires 1.0 milmil (0.001 inch) in diameter and 45 milmil long. Although the current under normal conditions is much less, such a wire will fuse (that is, melt and interrupt the current) when the current exceeds some 660 mAmA. A) Find the current density in the wire...

The single most important use of the element gold is for wires that join integrated circuits...

The single most important use of the element gold is for wires that join integrated circuits to the conducting pads that then connect microelectronic chips with external circuitry. A typical application uses gold wires 1.0 milmil (0.001 inch) in diameter and 60 milmil long. Although the current under normal conditions is much less, such a wire will fuse (that is, melt and interrupt the current) when the current exceeds some 550 mAmA. Find the current density in the wire when...

1. Five defective integrated circuits have accidentally passed the quality control inspection and shipped to a...

1. Five defective integrated circuits have accidentally passed the quality control inspection and shipped to a retailer in a batch of a total of 25 integrated circuits. Before selling them, the retailer decides to test the integrated circuits by randomly picking 10 integrated circuits out of the 25 that were shipped. (a) [10 points] What is the probability that there are exactly two defective integrated circuits in this sample of 10? (b) [10 points] What is the probability that there...

3. In a semiconductor company three machines, A, B, and C, fabricate integrated circuits (ICs). Machine...

3. In a semiconductor company three machines, A, B, and C, fabricate integrated circuits (ICs). Machine A produces 20% of the ICs, machine B produces 30% of the ICs, and machine C produces 50% of the ICs. The ICs are assumed to be identical. It is known that 3 in every 1000 ICs made by machine A are defective, 1 in every 125 ICs made by machine B is defective, and 1 in every 250 ICs made by machine C...

Subjects