Question

In: Mechanical Engineering

a)Using MIL STD 105E, find the sample size for inspection level III, normal inspection, AQL =...

a)Using MIL STD 105E, find the sample size for inspection level III, normal inspection, AQL = 1.5%, and lot size of 1000. Determine the sample size.

b)For inspection level I, tightened inspection, AQL = 6.5%, and lot size = 500, find the sample size using MIL STD 105E.

Solutions

Expert Solution

Standard MIL STD 105E AQL TABLE-For Question A- Lot Size= 1000 & Normal Inspection Level 3,

AQL= 1.5%

Code Letter for 1000 lot size is " K ".

For Question B- Lot Size= 500 & Tightned Inspection of Level 1,

AQL =6.5%

Code Letter for 500 lot size is " F ".

For Question A-

Locate Code letter " K ", and besides that, you will find the sample size = 125. (Ans)

Also at AQL=1.5%,

AC- 5, RE- 6

SO, lot is accepted if rejected part are less than or equal to 5 & lot is rejected if failed parts are equal or greater than 6.

For Question B- Inspection Level 1 (Tightned Inspection)

Above table is for Tightned Inspection.

If 2 lot are rejected in a row, than the inspection becomes Tightned, rather than Normal.

Locate Code letter " F ", AQL=6.5%

SAMPLE SIZE= 20.

Lot accepted if rejected parts are equal or lesser than 2.

Lot rejected if rejected parts are equal or greater than 3.


Related Solutions

Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size...
Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size is 600,000 units, the inspection is normal general level I. Acceptance quality level is 0.025% and the proportion of defective product in the lots is 0.4%. This is the question: what is the probability of accepting.
Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size...
Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size is 50,000 units, the inspection is normal general level II. Acceptance quality level is 0.065% and the proportion of defective product in the lots is 0.1% FIND Pa ( prop of acceptance)? PLEASE SHOW WORK!
Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size...
Using MIL STD 105 E, probability of accepting a lot acceptance number when the lot size is 600,000 units, the inspection is normal general level I. Acceptance quality level is 0.025% and the proportion of defective product in the lots is 0.4%. The correct answer is: 0.606.
With an inspection level III, if there are 15 rejections (AQL of 1.5) in a lot...
With an inspection level III, if there are 15 rejections (AQL of 1.5) in a lot size of 20000, will you accept or reject the whole lot? Explain with your answer
For a confidence level of 98% with a sample size of 28, find the critical t...
For a confidence level of 98% with a sample size of 28, find the critical t value. Critical Value = (round answer to 3 decimal places) Assume that a sample is used to estimate a population mean μμ. Find the 99.9% confidence interval for a sample of size 33 with a mean of 72.3 and a standard deviation of 12.1. Enter your answer accurate to one decimal place. I am 99.9% confident that the mean μμ is between  and Assume that...
At a .01 significance level with a sample size of 18, find the critical value for...
At a .01 significance level with a sample size of 18, find the critical value for the correlation coefficient of 1.
To test the following hypotheses at the 0.05 level of​ significance, using a sample size of...
To test the following hypotheses at the 0.05 level of​ significance, using a sample size of nequals=15. H00 ​: sigmaσsquared2equals=0.05 HSubscript Upper AA ​: sigmaσsquared2not equals≠0.05 What is the upper tail critical​ value? Round to three decimal places as needed. A. 27.488 B. 23.685 C. 26.119 D. 24.996
Use the normal approximation to find the indicated probability. The sample size is n, the population...
Use the normal approximation to find the indicated probability. The sample size is n, the population proportion of successes is p, and X is the number of successes in the sample. n = 85, p = 0.64: P(X > 52)
Find the critical value X2R corresponding to a sample size of 6 and a confidence level...
Find the critical value X2R corresponding to a sample size of 6 and a confidence level of 95 percent. Round to three decimal places.
Number of nonconformities in a process detected by inspection of sample size 50 are: 3, 2,...
Number of nonconformities in a process detected by inspection of sample size 50 are: 3, 2, 3, 1, 4, 0, 2, 3, 4, and 5. For sigma = 3: a. Construct a control chart for the fraction of nonconformities. b. Construct a control chart for the number of nonconformities. c. Can you conclude that this process is in statistical control? Why?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT