Question

In: Mechanical Engineering

Q1 . Design the rectangular key . Determine the shaft strength factor if the length of...

Q1 . Design the rectangular key . Determine the shaft strength factor if the length of the key should not exceed 12 cm .
used if need power 1kw velocity 500rpm ultimate stress 680Mpa yield stress 400Mpa shaft diameter50mm   tension=compression

Solutions

Expert Solution

The problem requires the concept of standard designing of keys and shaft strength factor. A detailed explanation is given below . Hope it would be helpful.

Hope the explanation would be helpful.


Related Solutions

: Determine the LRFD tensile design strength and the ASD tensile strength of the connection shown...
: Determine the LRFD tensile design strength and the ASD tensile strength of the connection shown if eight 7/8-in bolts are used in each flange to connect W18 X 76 with two 3/4 X 14-in plates. Include block shear calculations. (Fy = 50 ksi, Fu = 65 ksi)
1) Determine unmodified fatigue strength (units = MPa) of hot-rolled 1030 steel shaft in axial loading...
1) Determine unmodified fatigue strength (units = MPa) of hot-rolled 1030 steel shaft in axial loading for a design life of 10,000 cycles. Do not apply any fatigue correction factors. SN __________ MPa 2) Determine unmodified fatigue strength (units = ksi) for a normalized 4130 steel shaft in bending for a design life of 10^7 cycles. Do not apply any fatigue correction factors. SN __________ ksi 3) Determine unmodified fatigue strength (units = MPa) for cold-rolled 3003 aluminum rod in...
Design an experiment to determine the strength of the magnetic field of Earth using the available...
Design an experiment to determine the strength of the magnetic field of Earth using the available equipment. Available equipment: A large coil of wire (with stand in the center), compass, ammeter, 10Ω and 50Ω resistors, power supply, ruler. A) Perform the experiment and record your measurement and calculations in an appropriate format. Be explicit about what model you're using to calculate the magnetic field. Vector diagrams may assists you. Include important measurements. Determine the magnitude of the Earth's magnetic field....
Design an experiment to determine the strength of the magnetic field of Earth using the available...
Design an experiment to determine the strength of the magnetic field of Earth using the available equipment. Available equipment: A large coil of wire (with stand in the center), compass, ammeter, 10Ω and 50Ω resistors, power supply, ruler. A) Perform the experiment and record your measurement and calculations in an appropriate format. Be explicit about what model you're using to calculate the magnetic field. Vector diagrams may assists you. Include important measurements. Determine the magnitude of the Earth's magnetic field....
Design a rectangular milk carton box of width w, length ll, and height h which holds...
Design a rectangular milk carton box of width w, length ll, and height h which holds 540 cm^3 of milk. The sides of the box cost 1 cent/cm^2 and the top and bottom cost 3 cent/cm^2. Find the dimensions of the box that minimize the total cost of materials used.
What will be the length (L in meter) of a rectangular footing to support rectangular column...
What will be the length (L in meter) of a rectangular footing to support rectangular column 20x70 cm and carries a dead load of 625 kN and live load of 426 kN. The net allowable bearing pressure is 155 kPa. The design should be according to (ACI) code with the following parameters: fc’ = 28 MPa, fy = 420 MPa.
Rectangular Combined Footing design
Rectangular Combined Footing design
Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h,...
Design of Rectangular Beams with Tension Reinforcement Design a rectangular beam section (i.e., select b, h, and the required tension reinforcement) at midspan for a 22 ft-span simply supported beam that supports its own self-weight, a superimposed uniform dead load of 1.25 kip/ft, and a uniform live load of 2 kip/ft. The material properties are f 0 c = 4, 500 psi and fy = 60, 000 psi. Consider a clear cover of 1.5 inches to the #4 stirrups. Follow...
(a) In terms of relative strength, put fcd (design strength of concrete), fck (characteristic strength of...
(a) In terms of relative strength, put fcd (design strength of concrete), fck (characteristic strength of concrete) and fcm (mean strength of concrete) in order from lowest to highest strength. (3) (b) Approximately, what is the tensile strength of concrete as a percentage of its compressive strength? (1) (c) Draw and name all necessary reinforcement for the simply supported beam and static loading case shown at Figure 3a. (6) (d) Recreate the table in Figure 3b in your script books...
from QFD, what factor use to determine most important design specification? Is it the absolute weight...
from QFD, what factor use to determine most important design specification? Is it the absolute weight or relative weight? How can I list the order of importance of the design specification using data from QFD?
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT