Question

In: Electrical Engineering

A communication network has a bandwidth of 10 kHz. Calculate the signal-to-noise ratio in dB if...

A communication network has a bandwidth of 10 kHz. Calculate the signal-to-noise ratio in dB if the capacity of the channel for a 100Kbps [2 Marks]
ii. A communications channel with a bandwidth of 4kHz has a signal power to noise ratio of 7. Determine the Channel Capacity. [2 Marks]
ii. The bandwidth in b above is reduced by 25%. How much should the signal power be increased to maintain the same channel capacity?

Solutions

Expert Solution


Related Solutions

A normalized message signal has a bandwidth of W = 10 KHz and a power of...
A normalized message signal has a bandwidth of W = 10 KHz and a power of Pm= 0.75 . It is required to transmit this signal via a channel with an available bandwidth of 80 KHz and attenuation of 50 dB. The channel noise is additive and white with a power-spectral density of N0/2 = 10^(-10) watts/Hz. A frequency-modulation scheme, with no pre-emphasis/de-emphasis filtering, has been proposed for this purpose. 1. If it is desirable to have an SNR of...
Consider a message signal m(t) with bandwidth W = 5.86 kHz. This signal is applied to...
Consider a message signal m(t) with bandwidth W = 5.86 kHz. This signal is applied to a product modulator, together with a carrier wave c t = cos(210000πt) producing the DSB-SC modulated wave s(t). This modulated wave is next applied to a coherent detector producing an output signal y(t). The coherent detector consists of a product modulator that multiplies s(t) by c r = 2cos(222000πt) and a low pass filter which has a cut off frequency 21 kHz. The output...
Design an analog elliptic lowpass IIR filter with specifications Fp=10 kHz., Ap=1 dB, Fs=15 kHz. And...
Design an analog elliptic lowpass IIR filter with specifications Fp=10 kHz., Ap=1 dB, Fs=15 kHz. And As=50 dB. Provide the following plots in MATLAB: a. Magnitude b. Log-magnitude c. Group-delay d. Impulse response e. Pole-zero
If a signal to interference ratio of 16 dB is required for satisfactory forward channel performance...
If a signal to interference ratio of 16 dB is required for satisfactory forward channel performance of a cellular system, what is the frequency reuse factor and cluster size that should be used for maximum capacity. Consider the path loss exponent as n = 4 and n = 3. Assume that there are 6 co-channels cells in the first tier, and all of them are at the same distance from the mobile. Use suitable approximations.
Calculate the energy per bit per noise power density where the signal power is 10 Watts...
Calculate the energy per bit per noise power density where the signal power is 10 Watts and the bit is 10 Mbps in an environment of 27 degree celcius?
The ideal (daytime) noise-level for hospitals is 45 decibels with a standard deviation of 10 db;...
The ideal (daytime) noise-level for hospitals is 45 decibels with a standard deviation of 10 db; which is to say, this may not be true. A simple random sample of 81 hospitals at a moment during the day gives a mean noise level of 47 db. Assume that the standard deviation of noise level is really 10 db. All answers to two places after the decimal. (a) A 99% confidence interval for the actual mean noise level in hospitals is...
Specify the aliasing frequency of a signal that has a maximum frequency of 75 kHz and...
Specify the aliasing frequency of a signal that has a maximum frequency of 75 kHz and a sample frequency of 100 kHz. Use the folding diagram.
(a) What are two software methods of signal to noise ratio enhancement? (b) Briefly explain how...
(a) What are two software methods of signal to noise ratio enhancement? (b) Briefly explain how one of them works. Describe how signal to noise ratio affects LOD concentration.
Multichannel detectors like diode arrays and CCDs provide a signal to noise ratio (SNR) advantage by...
Multichannel detectors like diode arrays and CCDs provide a signal to noise ratio (SNR) advantage by the ability to measure many wavelengths simultaneously—a multiplex advantage. Consider the SNR for a photomultiplier tube (PMT), a diode array (DA), and a CCD. Assume the readout noise (RN) associated with these devices is 0 photoelectrons (pe-) for the PMT, 1000 pe- for the DA and 10 pe­‑ for the CCD. The readout noise is a constant number that does not change with exposure...
A type of foam ear plug has a 26 dB overall EPA noise reduction rating. Sally...
A type of foam ear plug has a 26 dB overall EPA noise reduction rating. Sally wants to sleep on her bus ride and decides to use these earplugs. The noise level inside the bus is 87 dB. (A) What noise level would she perceive with the ear plugs that have the 26 dB noise reduction? The reduced noise level would be _________ dB. (B) A loud rock band produces a sound level of 117 dB at a location near...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT