Question

In: Physics

.A student engineer is given a summer job to find the drag force on a new...

.A student engineer is given a summer job to find the drag force on a new unmaned aerial vehicle that travels at a cruising speed of 320 km/h in air at 15oC. The student decided to build a 1/50 scale model and test it in a water tunnel at the same temperature. (a) What conditions are required to ensure the similarity of scale model and prototype. (b) Find the water speed required to model the prototype. (c) If the drag force on the model is 5 kN, determine the drag force on the prototype

Solutions

Expert Solution


Related Solutions

Engineering student Bryan has a high-paid summer job as a forklift operator. This job enables him...
Engineering student Bryan has a high-paid summer job as a forklift operator. This job enables him to attend college without having to take out any student loans. He is now staring at a 50- gallon drum filled with used machine coolant, wondering what he should do. Just moments ago, Bryan’s supervisor, Max, told him to dump half of the used coolant down the drain. Knowing the coolant was toxic, Bryan noted this to Max, but Max was not swayed. Max:...
Recall a time in a co-op placement, a summer job, an internship, a student club, a...
Recall a time in a co-op placement, a summer job, an internship, a student club, a student team project, etc. when your values conflicted with what you were expected to do in a particular, nontrivial decision, and you spoke up and acted to resolve the conflict. Consider the following and write down your thoughts: What did you do, and what was the impact? What motivated you to speak up and act? Identify the values that conflicted with what you were...
When a parachute opens, the air exerts a large drag force on it. This upward force...
When a parachute opens, the air exerts a large drag force on it. This upward force is initially greater than the weight of the sky diver and, thus, slows him down. Suppose the weight of the sky diver is 852 N and the drag force has a magnitude of 1018 N. The mass of the sky diver is 86.9 kg. Take upward to be the positive direction. What is his acceleration, including sign?
A new graduate enters the work force and is looking for a job. She is considered:...
A new graduate enters the work force and is looking for a job. She is considered: A. cyclically unemployed. B. underemployed. C. frictionally unemployed. D. naturally unemployed.
a=2 b=1 A bullet is to be tested in the laboratory to determine the drag force...
a=2 b=1 A bullet is to be tested in the laboratory to determine the drag force on it. Dependent parameter the drag force D (Newton) depends on the velocity of the bullet V(m/s), the length of the bullet L(m), sound velocity c(m/s), density of fluid ρ (kg/m3) and dynamic viscosity µ(kg/ms). Solve the problem by making the necessary assumptions and drawing the schematic figure I-Determine the nondimensional p parameters using repeating variables ii-a bullet with a speed of 9a,b m/s...
If a golf ball were dropped from a significant height and the force of Drag is...
If a golf ball were dropped from a significant height and the force of Drag is modeled by Fd=0.0057*V-0.0106, where V is the velocity in m/s the Fd is the force of drag in N. The mass of the golf ball is 0.0455 Kg. h. How high will the golf ball bounce after the 5th impact with the concrete surface ignore drag force? i. If drag was included for G and H what type of analysis technique would be needed
4- If the drag force on a smooth sphere depends on the velocity (V), sphere diameter...
4- If the drag force on a smooth sphere depends on the velocity (V), sphere diameter (D), viscosity (?), and density (?), use dimensional analysis to show the drag coefficient on the sphere is a function of the Reynolds number only. (15%) ?
Running on a treadmill is slightly easier than running outside because there is no drag force...
Running on a treadmill is slightly easier than running outside because there is no drag force to work against. Suppose a 60 kg runner completes a 5.0 km race in 22 minutes. a) Determine the drag force on the runner during the race. Suppose that the cross section area of the runner is 0.72 m2m2. b) What is this force as a fraction of the runner's weight?
A project engineer was given the assignment to determine which model of a new excavator the...
A project engineer was given the assignment to determine which model of a new excavator the company should purchase based on an interest rate of 10 percent per year. Model A - will cost $100,000 to purchase (year 0) and will generate $15,000 income each year for next 10 years (years 1-10) Model B- will cost $150,000 to purchase (year 0) and will generate $20,000 income each year for next 10 years (years 1-10) A) Draw the cash flow diagram...
Can you write essay with 300-450 words related to these keywords? 1-Drag force 2- Lift force...
Can you write essay with 300-450 words related to these keywords? 1-Drag force 2- Lift force 3- Omnidirectional 4- Pitch control 5- Stall control 6- Yaw motor
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT