Question

In: Operations Management

1. The Radiologist team have purchased a new MRI scanner. Briefly explain how engineering drawings will...

1. The Radiologist team have purchased a new MRI scanner. Briefly explain how engineering drawings will be used during installation?

2. What are the seven (7) types of logic gates (different diagram standards accepted) and their associated truth tables, for each gate provide the name,common graphic symbol and truth table?

Solutions

Expert Solution

Above image just help you for your better understanding.

This plan needs to take workflow and MRI system requirements into account, and should include:

* Scan Room

* Control Room

* Computer Equipment Room

Your architect and engineer will need to review the typical and equipment site plan and supply engineering requirement to allocate space appropriately for workflow and system operatin. These include:

* system delivery path

* floor loading requirement

* floor leveling

* ceiling height requirements

* access for cryogens

* cryogen venting

* access for cryogen venting according to designs

* chiller area

* cryogen access and storage

The RF and Magnetic Shielding designs should be based on measurements taken by he RF and shielding manufacture. The goal is to protect the magnetic field homogeneity. The shielding company will then provide you with a site specific room plan. This will include:

* Amount and location of steel shielding (if needed)

* location and shimming requirements for structural steel

* Method to deal with moving ferrous object.

  • Design of RF Shielded door and windows
  • Patient protection for ferrous materials
  • Acoustic Shielding
  • Appropriate filters   

The Secondary MRI Area will include:

  • PACS/RIS/Network Area
  • Patient Dressing and Preparation Area
  • Soiled and Clean Areas
  • Patient Waiting and Reception area

Support Areas will include

  • Administrative Area
  • Meetings room
  • Storage area

Pre Construction considerations include:

  • Delivery Path of Magnet
  • Chiller area
  • Facility HVAC systems
  • Fire protection

HVAC, Electrical and Mechanical Requirements include:

  • HVAC for MRI Suite, Control Room and Computer Room
  • Cryogen Venting
  • Fire Detection

ANSWER 2)

The 7 Logic Gates are as follows:

  1. AND Gate
  2. OR Gate
  3. XOR Gate
  4. NOT Gate
  5. NAND Gate
  6. NOR Gate
  7. XNOR Gate


Related Solutions

Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating...
Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating cost is $225,000 per year and it can be sold for $130,000 anytime in the next 3 years. The Center’s director is considering replacing the presently owned MRI scanner with a state-of-the-art 3 Tesla machine that will cost $2 million.The operating cost of the new machine will be $420,000 per year, but it will generate extra revenue that is expected to amount to $500,000...
Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating...
Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating cost is $425,000 per year and it can be sold for $165,000 anytime in the next 3 years. The Center’s director is considering replacing the presently owned MRI scanner with a state-of-the-art 3 Tesla machine that will cost $2.5 million.The operating cost of the new machine will be $380,000 per year, but it will generate extra revenue that is expected to amount to $625,000...
Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating...
Huntington Medical Center purchased a used low-field MRI scanner 2 years ago for $445,000. Its operating cost is $375,000 per year and it can be sold for $155,000 anytime in the next 3 years. The Center’s director is considering replacing the presently owned MRI scanner with a state-of-the-art 3 Tesla machine that will cost $2.5 million.The operating cost of the new machine will be $300,000 per year, but it will generate extra revenue that is expected to amount to $575,000...
A healthcare company purchased a new MRI machine on 1/1/X3. At year-end the company recorded a...
A healthcare company purchased a new MRI machine on 1/1/X3. At year-end the company recorded a straight-line deprecation expense of $75,000 for book purposes and double-declining balance depreciation expense of $94,000 for tax purposes. Management estimates warranty expense in 20X3 to be $150,000. The company's tax rate is 37%. Assuming these are the only relevant entries for deferred taxes, the company's recorded change in deferred tax asset and liabilities on 12/31/X3 are closest
1. What are the four different stages that engineering drawings may be used for, Give a...
1. What are the four different stages that engineering drawings may be used for, Give a short explanation of each stage? 2. List twenty (20) items that could be found on a typical engineering drawing?
PHYS/BIOL 464 Medical Imaging Instrumentation MRI HW 8A 1. For a scanner with a maximum gradient...
PHYS/BIOL 464 Medical Imaging Instrumentation MRI HW 8A 1. For a scanner with a maximum gradient strength of 20 mT m-1 and a minimum transmitted bandwidth of 0.9 kHz, what is the thinnest slice that can be selected? (? = 42.6 MHz T-1). 2. Which of the following is the bandwidth of a pulse with frequencies from 60.0015 to 60.0045 MHz? (a) 3 kHz (b) 3 MHz (c) 0.3 Mhz (d) 60.0030 MHz. 3. Convert the following gradient strengths, expressed...
How python can be used in civil engineering? please explain briefly
How python can be used in civil engineering? please explain briefly
Give an example of how annealing is used in an engineering application. Also, briefly explain how...
Give an example of how annealing is used in an engineering application. Also, briefly explain how and why the mechanical properties—for a metal—of yield strength, ductility, hardness, Young’s modulus, ultimate tensile strength, and toughness are different for a cold worked metal vs a metal that has been annealed at a relatively high temperature for a relatively long time (must talk about grain size).
Briefly explain the steps of team building process
Briefly explain the steps of team building process
You are the engineering representative on a team for a new product introduction. The proposed manufacturing...
You are the engineering representative on a team for a new product introduction. The proposed manufacturing process uses a semi-automated machine along with people. Components for each unit of the product cost $8. The semi-automated machine costs $1,500,000, and it has a 7-year MACRS recovery period. The salvage value is $0 for this specially designed machine. This machine can manufacture 175 finished parts per hour. Table 29-1 Production Volume (1000’s) Year: 1 2 3 4 5 6 7 8 9...
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT