Question

In: Mechanical Engineering

An external gear has a module of 4, 52 teeth in the gear, 28 teeth in...

An external gear has a module of 4, 52 teeth in the gear, 28 teeth in the pinion, a pressure angle of 20°, pinion rotational speed of 1500 rpm, face width of 20 mm, and gear and pinion material having modulus of elasticity of 206 GPa and Poisson’s ratio of 0.3. The Hertzian contact pressure is 0.980 GPa. The lubricant used has an absolute viscosity of 0.3 Pa-s and pressure viscosity coefficient of 2.2 x 10-8 m2/N. The root-mean-square surface roughness for both the pinion and gear is 0.1 µm. Determine the following:

  1. Transmitted power
  2. Minimum film thickness
  3. The film parameter

Solutions

Expert Solution

samet mamat answered 3 months ago
Next > < Previous

Related Solutions

Sun Gear Planet Gear Ring Gear Quantity 1 3 1 Module 2 2 2 Teeth 22...
Sun Gear Planet Gear Ring Gear Quantity 1 3 1 Module 2 2 2 Teeth 22 Pressure Angle 20 degrees 20 degrees 20 degrees Pitch Diameter Complete the table above and show solution if possible Additional specifications: -Unit is in metric (mm) -the ring gear is stationary -the ratio is 10:1 (meaning the sun gear must complete 10 revolutions for each revolution of the output carrier)
One method in which gear tooth interference can be avoided is to lengthen the pinion teeth...
One method in which gear tooth interference can be avoided is to lengthen the pinion teeth and shorten the gear teeth. A 12 tooth pinion with a diametral pitch of 2 teeth/in and a pressure angle of (φ = 20°) is to be meshed with a 60 tooth gear at a center distance of 18 inches. Calculate the maximum addendum length of the gear teeth if there is to be no interference. Then calculate the addendum length of the pinion...
List 4 External Opportunities Sam's Club has and 4 External Threats Sam's Club has.
List 4 External Opportunities Sam's Club has and 4 External Threats Sam's Club has.
A plastic gear manufacturer is invstigating a new gear, which the company claims it has a...
A plastic gear manufacturer is invstigating a new gear, which the company claims it has a mean diameter of 12cm with a standard deviation of .5cm. The company wishes to test the hypothesis Ho: mu=12 against H1: Mu < 12 using a random sample of 16 specimens. What is the type 1 error if the critical region is defined as x< 11.5cm? Fine B for the case in which the true mean diameter is 11.25cs Fine B for the case...
Module 4: Chatter Corporation operates in an industry that has a high rate of bad debts....
Module 4: Chatter Corporation operates in an industry that has a high rate of bad debts. Before any year-end adjustments, the balance in Chatter’s accounts receivable account is $556,000, and the allowance for doubtful accounts has a debit balance of $5,000. The year-end balance reported in the balance sheet for the allowance for doubtful accounts will be based on the aging schedule shown here: Days Account Outstanding Amount Probability of Collection Less than 16 days $293,000 .97 Between 16 and...
A bond with a face value of $10,000 has 4 years and 28 days left to...
A bond with a face value of $10,000 has 4 years and 28 days left to maturity. The coupon rate is 4%. Interest payments are paid quarterly. The bond will be discounted at an annual rate of 8%. Diagram the cash flows of this bond. What is the current price of this bond? How is the extra 28 days handled in the pricing of the bond? What are the risks of this bond? (looking for 2 risks on bonds)
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the...
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the production quality, you sample 30 gears and find the average to be 4.11 with a standard deviation of 0.67. Construct a hypothesis test at a 0.05 level of significance to determine if the gear diameter is larger than 4 inches. Select one: a. The critical value is 2.05, the test statistic is 0.90, conclude the gear diameter is not equal to 4 inches b....
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the...
The design of an automotive gear requires the diameter to be 4 inches. To evaluate the production quality, you sample 30 gears and find the average to be 4.08 with a standard deviation of 0.71. Construct a hypothesis test at a 0.05 level of significance to determine if the gear diameter is larger than 4 inches. Select one: a. The critical value is 1.70, the test statistic is 0.62, conclude the gear diameter is less than or equal to 4...
National League Gear has two classes of stock authorized: 4%, $20 par preferred, and $5 par...
National League Gear has two classes of stock authorized: 4%, $20 par preferred, and $5 par value common. The following transactions affect stockholders’ equity during 2021, National League’s first year of operations: February 2 Issue 1.5 million shares of common stock for $35 per share. February 4 Issue 600,000 shares of preferred stock for $23 per share. June 15 Purchase 150,000 shares of its own common stock for $30 per share. August 15 Resell 112,500 shares of treasury stock for...
National League Gear has two classes of stock authorized: 4%, $20 par preferred, and $5 par...
National League Gear has two classes of stock authorized: 4%, $20 par preferred, and $5 par value common. The following transactions affect stockholders’ equity during 2021, National League’s first year of operations: February 2 Issue 1.5 million shares of common stock for $35 per share. February 4 Issue 600,000 shares of preferred stock for $23 per share. June 15 Purchase 150,000 shares of its own common stock for $30 per share. August 15 Resell 112,500 shares of treasury stock for...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT