Question

In: Other

5 kg of butane (C4H10), contained in a piston-cylinder device undergoes a process from P1 =...

5 kg of butane (C4H10), contained in a piston-cylinder device undergoes a process from P1 = 5 MPa, T1 = 500 K to P2 = 3 MPa and T2 = 450 K during which the relationship between pressure and specific volume is PVn = C.
a. Using the data from Generalized Compressibility chart, determine the amount of work done during the process.

b. If butane is assumed an ideal gas, how would you compare the work done during the process to the one that you have obtained above.
QUESTION 9 (PO2, CO2, C6)
For a system that contains butane as described in the above question (QUESTION 8), by making appropriate assumptions, investigate and discuss the effect of polytopic exponent on work boundary and heat transfer, for the system to reach the same:
a. final volume. b. final pressure ( 25 marks )

PLEASE ANSWER QUESTION 9 ACCORDING TO GIVEN MARKS

Solutions

Expert Solution

Amanda K answered 4 months ago
Next > < Previous

Related Solutions

Five kg of butane (C4H10) in a piston–cylinder assembly undergo a process from p1 = 5...
Five kg of butane (C4H10) in a piston–cylinder assembly undergo a process from p1 = 5 MPa, T1 = 500 K to p2 = 2 MPa, T2 = 450 K during which the relationship between pressure and specific volume is pvn = constant. Determine the work, in kJ.
An ideal gas is contained in a piston-cylinder device and undergoes a power cycle as follows:...
An ideal gas is contained in a piston-cylinder device and undergoes a power cycle as follows: 1-2 isentropic compression from an initial temperature T1 5 208C with a compression ratio r 5 5 2-3 constant pressure heat addition 3-1 constant volume heat rejection The gas has constant specific heats with cv 5 0.7 kJ/kg·K and R 5 0.3 kJ/kg·K. (a) Sketch the P-v and T-s diagrams for the cycle. (b) Determine the heat and work interactions for each pro- cess,...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 7 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.4, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 3 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.2, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 =...
Air undergoes a polytropic process in a piston–cylinder assembly from p1 = 1 bar, T1 = 295 K to p2 = 3 bar. The air is modeled as an ideal gas and kinetic and potential energy effects are negligible. For a polytropic exponent of 1.6, determine the work and heat transfer, each in kJ per kg of air, (1) assuming constant cv evaluated at 300 K. (2) assuming variable specific heats.
A mass of 0.3 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 240...
A mass of 0.3 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 240 kPa. Initially, 70 percent of the mass is in the liquid phase. Now heat is transferred to the refrigerant at constant pressure until the cylinder contains vapor only. (a) show the process on a P-v and T-v diagrams with respect to saturation lines. Determine; (b) the volume occupied by the refrigerant initially, (c) the work done, and (d) the total heat transfer.
A mass of 0.3 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 240...
A mass of 0.3 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 240 kPa. Initially, 70 percent of the mass is in the liquid phase. Now heat is transferred to the refrigerant at constant pressure until the cylinder contains vapor only. (a) show the process on a P-v and T-v diagrams with respect to saturation lines. Determine; (b) the volume occupied by the refrigerant initially, (c) the work done, and (d) the total heat transfer.
100 kg of R-134a at 320 kPa are contained in a piston-cylinder device whose volume is...
100 kg of R-134a at 320 kPa are contained in a piston-cylinder device whose volume is 7.530 m3. The piston is now moved until the volume is one-half its original size. This is done such that the pressure of the R-134a does not change. Determine the final temperature and the change in the total internal energy of the R-134a. (Round the final answers to two decimal places.)
100 kg of R-134a at 200 kPa are contained in a piston–cylinder device whose volume is...
100 kg of R-134a at 200 kPa are contained in a piston–cylinder device whose volume is 12.766 m3. The piston is now moved until the volume is one-half its original size. This is done such that the pressure of the R-134a does not change. Determine the final temperature and the change in the total internal energy of R-134a. Use data from the steam tables. The final temperature is  °C. The total change in internal energy is  kJ/kg.
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests...
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests on lower stops such that the volume occupied by the water is 0.835 m3. The cylinder is fitted with an upper set of stops. When the piston rests against the upper stops, the volume enclosed by the piston-cylinder device is 0.841 m3. A pressure of 200 kPa is required to support the piston. Heat is added to the water until the water exists as...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT