Question
In: Physics
An empty tin can with height of 30cm and a diameter of 15cm is open at...
An empty tin can with height of 30cm and a diameter of 15cm is open at one end and closed at the other end. If the vertical can, with open end down, be slowly immersed in water, how far the water will rise inside the can when the closed end is 10 cm below the water surface?
I know this is easy, but when I'm solving for h, I'm getting a negative value, means that the can will be filled completely?
Solutions
genius_generous answered 6 months agoRelated Solutions
An empty tin can with height of 30cm and a diameter of 15cm is open at...
An empty tin can with height of 30cm and a diameter of 15cm is
open at one end and closed at the other end. If the vertical can,
with open end down, be slowly immersed in water, how far the water
will rise inside the can when the closed end is 10 cm below the
water surface?
A siphon consisting of a pipe of 15cm diameter is used to empty kerosene oil (s...
A siphon consisting of a pipe of 15cm diameter is used
to empty kerosene oil (s = 0.8) from a tank A.
The siphon discharges to the atmosphere at an elevation of 1m. the
oil surface in the tank is at ana
elevation of 4m. The centerline of the siphon pipe at its highest
point C is at an elevation of 5.5m. The
losses in the pipe are 0.5m up to the summit and 1.2m from the
summit to the...
A signal with a wavelength of 15cm goes through a car window that is 30cm wide...
A
signal with a wavelength of 15cm goes through a car window that is
30cm wide and has an extension of 6m deep. What is linear width of
the signal's central max at the end of the car?
Two thin lens (f1 = 15cm, f2 = −30cm) are separated by a distance d =...
Two thin lens (f1 = 15cm, f2 = −30cm) are
separated by a distance d = 10cm.
(a) (10 points) Find the matrix of the system.
(b) (15 points) If 2cm tall object is placed on the distance 30cm
to the left from the first lens. Find
the position and the size of the image by using matrix
method.
(c) (25 points) Find positions of the cardinal points of the
system. Find the position and the size of
the image...
A disk is cast in an open mould with diameter 25 cm and height 15 mm....
A disk is cast in an open mould with diameter 25 cm and height
15 mm. The pouring temperature is 1200°C. Calculate the total heat
evolved during cooling if the disk was cast in copper, and given
that the heat of fusion is 200 kJ/kg.
given a 5.0m pipe measured end to end with an inner diameter of 15cm and a...
given a 5.0m pipe measured end to end with an inner
diameter of 15cm and a variable frequency mini speaker. assumed an
air temperature of 30°C(hot).
a. one end of the pipe is closed by taping a circular wood cylinder
over the hole at one end. the wood does not go inside the pipe,it
covers its the hole. compute the lowest audible resonant frequency
of the pipe.
b. sketch the node antinode pattern in the pipe for the resonant
frequency...
Mining Engineering At a open pit mine the bench height is 15m, the vertical blasthole diameter...
Mining Engineering
At a open pit mine the bench height is 15m, the vertical
blasthole diameter is 250mm and the rock has a specific gravity of
2.9. If ANFO with a density of 0.8g/cc is used with a square
pattern where S = B, determine: 1. Burden 2. Spacing 3. Subdrill 4.
Stemming length 5. Blasthole length 6. Charged length 7. Rock
broken/blasthole 8. Powder factor
Is my proof that empty set is open and R is open correct?
Is that empty set is open and R is open correct? Give details Explaination.
An open-top box is to be made from a 20cm by 30cm piece of cardboard by...
An open-top box is to be made from a 20cm by 30cm piece of
cardboard by removing a square from each corner of the box and
folding up the flaps on each side. What size square should be cut
out of each corner to get a box with the maximum volume?
A centrifugal pump with an impeller diameter of 30cm and speed 1800RPM operating at its best...
A centrifugal pump with an impeller diameter of 30cm and speed
1800RPM operating at its best effiecieny point develops a head of
30m and a flow of 3900L/min. while requiring power of 24kW. This
pump is scaled up to provide a flow of 11000L/min. and a head of
75m. Determine the impeller diameter, speed, and a brake power of
the new pump.
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- A: Provide a numerical example of how Earned Value Management may mislead us as to whether...
- Daryl wishes to save money to provide for his retirement. Beginning one month from now, he...
- L= {w belongs to {0,1}* | the number of 0's is a prime number} . Prove...
- What are Foyal's five management functions? Identify which organizational units accomplish these functions in your airport...
- An air conditioning unit, where water condensation is allowed, cools 9,791 m3 / min of humid...
- how do u calculate value of a bond You consider purchasing $1000 face value 7 year...
- Why am I getting this error using 000webhost , but I do not get this error...
ADVERTISEMENT