1.Answer the following questions. a)A solid shaft transmits 75kW power at 200rpm.Determine the diameter of the...

1.Answer the following questions.

a)A solid shaft transmits 75kW power at 200rpm.Determine the diameter of the shaft if the twist in the shaft is not exceeded 1⁰ in 1m length of the shaft, and shear stress is limited to 50N/mm^2.

Take rigidity modulus, G=100kN/mm^2

b)A hollow shaft with a diameter ratio of 0.7(internal outside) is required to transmit 500kW at 300 rpm with a uniform twisting moment. Allowable shear stress in the material is 70N/mm^2 and twist in a length of 2.5m is not to exceed 1⁰.Determine the maximum external diameter of the shaft satisfying these conditions. Take modulus of rigidity G= 80KN/mm^2

Expert Solution

Ally Wells answered 7 months ago

A solid and hollow shaft, connected by a coupling, transmit power. The outside diameters of the...

A solid and hollow shaft, connected by a coupling, transmit power. The outside diameters of the shafts are the same and the inside diameter of the hollow shaft is 75% of its outside diameter. The solid shaft is three times as long as the hollow shaft. Take the modulus of rigidity for both shafts as 80 GPa. (a) If the angle of twist for the solid shaft is 1 degree, find the angle of twist for the hollow shaft. (b)...

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a...

3.7-4 A solid steel shaft ABC with diameter d=40 mm is driven at A by a motor that transmits 75kW to the shaft at 15 Hz. The gears at B and C drive machinery requiring power equal to 50kW and 25 kW, respectively. Compare the maximum shear stress and angle of twist in the shaft between the motor at A and the gear at C. Assume that G=75 GPa.

Part B. The worm shaft shown in part a of the figure transmits 1.2 hp at...

Part B. The worm shaft shown in part a of the figure transmits 1.2 hp at 500 rev/min. A static force analysis gave the results shown in part b of the figure. Bearing A is to be an angular-contact ball bearing mounted to take the 555-lbf thrust load. The bearing at B is to take only the radial load, so a straight roller bearing will be employed. Use an application factor of 1.3, a desired life of 30 kh, and...

Answer the following questions: Part A: Volumes of Revolution a) Find the volume of the solid...

Answer the following questions: Part A: Volumes of Revolution a) Find the volume of the solid obtained when the region bounded by y = 1/x , and the lines x = 1, x = 3 and y = 0 is rotated about the x-axis. b) Find the volume of the solid obtained by revolving the region bounded by the parabolas y = x^2 and y^2 = 8x about the x-axis. c) Find the volume of the solid obtained by revolving...

how to calculate a shaft diameter of horizontal wind turbine

A steel shaft is to be manufactured either as a solid circular bar or as a...

A steel shaft is to be manufactured either as a solid circular bar or as a circular tube. The shaft is required to transmit a torque of 1200 N_m without exceeding an allowable shear stress of 40 MPa nor an allowable rate of twist of0.75°/m. (The shear modulus of elasticity of the steel is 78 GPa.). Determine the required outer diameter do of the solid shaft [58.8 mm] Determine the required diameter d2of the hollow shaft if thethickness t of...

A 900 MW power station transmits power at a potential difference of 60, 000 V a)...

A 900 MW power station transmits power at a potential difference of 60, 000 V a) Find the current. b) Write down the equation for the resistance in terms of the resistivity. c) If the power loss is 110 MW, over the length of the 200 km power line, find the resistivity of the line, if its cross section is 9 cm 2. d) Write down the equation for the magnetic field due to a long conductor. e) Find the...

Answer the following questions based on the reaction: K2CrO4 + AgNO3 ---> red solid. A: What...

Answer the following questions based on the reaction: K2CrO4 + AgNO3 ---> red solid. A: What is the formula for the solid produced? B: Using the reaction above, a chemestry student has 35 mL of a .250 M solution of silver nitrate. How many milliliters of .105 M K2CrO4 will be required to react completely with the silver ion present. C: Considering the reaction in part b, how many grams of product will be formed?

A cordless phone transmits at 900 MHz at a power of 10 mW. Since this is...

A cordless phone transmits at 900 MHz at a power of 10 mW. Since this is in air, the speed of the wave is essentially 3.00x108 m/s. What is the wavelength of the electromagnetic wave coming from the phone? What is the power per area 0.030 m away from the phone? Assume a spherical propagation of energy and the area of a sphere is 4pr2 What are the maximum electric (E0) and magnetic field (B0) strengths at 0.030 m from...

The diameter of a cylindrical shaft door hinge is normally distributed with a population mean of...

The diameter of a cylindrical shaft door hinge is normally distributed with a population mean of 12.8 mm and a standard deviation of 0.35 mm. The specifications on the shaft are 13 ± 0.15 mm. What proportion of shafts conforms to the specifications?

Question