Question

In: Civil Engineering

A cantilevered one way slab of effective span 1.5 m has an effective depth of 100...

A cantilevered one way slab of effective span 1.5 m has an effective depth of 100 mm. The slab is provided with 10 mm dia. main reinforcement at 150 mm c/c spacing. Check the slab for deflection if, Ast required is 522.02 mm2. The grade of concrete is M20 and grade of steel is Fe 415.

Expert Solution

Ally Wells answered 7 months ago

A one-way slab has been designed for a simply supported span of 4.0 m with an...

A one-way slab has been designed for a simply supported span of 4.0 m with an overall depth of 170 mm and clear cover of 20 mm, using M 20 concrete and Fe 415 steel. The dead loads are taken as 5.0 kN/m2 and the live loads as 2.0 kN/m2. The longitudinal bars are designed as 10 mm φ @ 150 c/c. Verify the adequacy of the thickness provided, Applying the limiting span/effective depth ratio; Actual calculation of total deflections.

A one-way solid concrete slab is to be used for a simple span of 18 ft....

A one-way solid concrete slab is to be used for a simple span of 18 ft. In addition to its own weight, the slab carries a superimposed dead load of 50 psf and a live load of 75 psf. Using the strength method with f ′c = 4 ksi and fy = 60 ksi, design the slab for minimum overall thickness. (account for weight of slab)

Design of circular slab with simply supported condition. Effective span = 5.4 m c/c Floor finish...

Design of circular slab with simply supported condition. Effective span = 5.4 m c/c Floor finish = 1.5 kN/m2 Imposed load = 3 kN/m2 Characteristic strength of concrete (fck) = 35N/mm2 Characteristic strength of steel (fyk) = 500 N/mm2 Assume cover

Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a...

Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf (the dead load does not include the self-weight of the slab). Use f’c = 3000 psi and Fy = 60,000 psi. Make the slab thickness to 1/2-in. increments.

A square foundation 1.5? × 1.5? is founded at a depth of 1.5 m below the...

A square foundation 1.5? × 1.5? is founded at a depth of 1.5 m below the ground surface in sand soil having a cohesion ? ′ = 0 ?? ?2 ⁄ and angle of shearing resistance∅ ′ = 33° . The water table is at a depth of 6 m below ground level. The unit weight of soil above the water table is ? = 18 ?? ?3 ⁄ and the saturated unit weight of the soil ???? = 19...

A beam with a cross-section of 0.3 m x 0.7 m has an effective depth of...

A beam with a cross-section of 0.3 m x 0.7 m has an effective depth of 0.638 m and a span of 4.30 m. Use the following data below to determine (a) the steel requirement due to flexure, (b) ultimate threshold torsion, and (c) spacing of stirrup due to combined shear and torsion: Mu = 322 KN-m Vu = 317 KN Tu = 42 KN-m f'c =28 MPa fyt = 414 MPa 12 mm stirrup diameter cover of 0.04 m

A footing of size 1.5×2 m is located at depth 1.2 m on a soil with...

A footing of size 1.5×2 m is located at depth 1.2 m on a soil with bulk unit weight of b=16.8 kN/m3 and sat = 17.6 kN/m3, c’ = 80 kN/m2 and ’ = 0. Determine the gross allowable load of the footing for (a) ground water table well below the foundation base, and (b) ground water table at the ground surface. Compare the results to see if in this case, the position of ground water table has an effect...

prestressed road bridge of span 16.74 m consists of a concrete slab of 420 mm thick...

prestressed road bridge of span 16.74 m consists of a concrete slab of 420 mm thick with parallel post-tensioned cables, in each of which the force at transfer is 440 kN. If the bridge is required to support a uniformly distributed applied load of 43.37kN/m2 , with tensile stress in the concrete not exceeding 0.85 N/mm2 at any time. Calculate the maximum horizontal spacing of the cables, their distance from the soffit of the slab at mid-span and their lowest...

In a rectangular cross-section canal with a width of 10 m and a depth of 1.5...

In a rectangular cross-section canal with a width of 10 m and a depth of 1.5 m, uniform and Continuous current monitoring is applied. The channel's Manning coefficient includes 0.015. Base because its slope is 0.0005. Considering this information a) By writing the numerical magnitude of water face slope and energy line slope and its rationale Set. b) Calculate the speed of the current in the channel. c) Calculate the flow of the current in the channel. d ) When...

Design and draw the final cross section of a one-way reinforced concrete slab for the inside...

Design and draw the final cross section of a one-way reinforced concrete slab for the inside of a building, where the span is l =3,6 m, and the applied live load is LL = 7,02 KN m2 ⁄ . Normal-weight aggregate concrete is specified with a density of 23. 5 KN m3 ⁄(reinforcement weight is included). Use the largest of claculated steel ratio ρ and 0.75ρmax. Assume: Es = 2 × 105 MPa, fc′ = 28 MPa and fy =...