Question

In: Mechanical Engineering

A quality mixture of water is contained in a piston cylinder system at a pressure of...

A quality mixture of water is contained in a piston cylinder system at a pressure of 3 bar. The initial volume of the system is 3 m3, and saturated liquid occupies 0.3 m3. Heat is added to the system and the volume is allowed to triple before a stop is reached. The final state of the system is at pressure of 30 bar. If the external pressure is 1 bar determine the followng: (a) The amount of heat added to the system; and (b) the amound of work performed by the system.

Solutions

Expert Solution


Related Solutions

A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder...
A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 175 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. An electrical heater is in operation, and the piston rises until it hits a set of stops, which are set at double the initial volume. Electrical heating continues until the pressure reaches 500 kPa. Determine (a) the initial and final temperatures,...
A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder...
A mass of 3 kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 175 kPa. Initially, 2 kg of the water is in the liquid phase and the rest is in the vapor phase. An electrical heater is in operation, and the piston rises until it hits a set of stops, which are set at double the initial volume. Electrical heating continues until the pressure reaches 500 kPa. Determine (a) the initial and final temperatures,...
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests...
One kilogram of water is contained in a piston-cylinder device at 100 degC. The piston rests on lower stops such that the volume occupied by the water is 0.835 m3. The cylinder is fitted with an upper set of stops. When the piston rests against the upper stops, the volume enclosed by the piston-cylinder device is 0.841 m3. A pressure of 200 kPa is required to support the piston. Heat is added to the water until the water exists as...
0.5 kg of R12 are contained in a piston/cylinder and has a quality of 75% and...
0.5 kg of R12 are contained in a piston/cylinder and has a quality of 75% and a temperature of 0 C. Heat is transferred at constant pressure until the R12 is a saturated vapor. Determine: a) the initial volume of the R12; b) the work done; c) the heat transfer; d) the T-v diagram. Ans: a) 0.0208 m3 b) 2.13 kJ c) 18.9 kJ
Two kilograms of CO2 gas is contained in a piston-cylinder assembly at a pressure of 6.5...
Two kilograms of CO2 gas is contained in a piston-cylinder assembly at a pressure of 6.5 bar and a temperature of 300 K. The piston has a mass of 5000 kg and surface area of 1m2. The friction of the piston on the walls is significant and cannot be ignored. The atmospheric pressure is 1.01325 bar. The latch holding the piston in position is suddenly removed and the gas is allowed to expand. The expansion is arrested when the volume...
Oxygen is contained in a piston-cylinder system initially at a temperature of 40 oC and a...
Oxygen is contained in a piston-cylinder system initially at a temperature of 40 oC and a pressure of 150 kPa. The piston is 1 m in diameter and initially 20 cm above the base of the cylinder. Heat is added at constant pressure until the piston has moved 30 cm, so it's now at 50 cm. I found the mass of the system to be 0.2898 kg, and T2 = 783K. a) Using the table of properties of oxygen as...
Water contained in a piston-cylinder assembly as shown in the Figure below, initially at 1.5 ???...
Water contained in a piston-cylinder assembly as shown in the Figure below, initially at 1.5 ??? and a quality of 20%, is heated at a constant pressure until the piston hits the stops. Heating then continues until the water is saturated vapor. Show the processes of the water in series on a sketch of the ?-? diagram. For the overall process of the water, evaluate the work and heat transfer, each in ??⁄??. Kinetic and potential effects are negligible. (please...
With a pressure of 0.4MPa, 2kg of water vapor is contained in a cylinder of 0.4m3,...
With a pressure of 0.4MPa, 2kg of water vapor is contained in a cylinder of 0.4m3, and the cylinder is connected to the piston. When keeping the pressure constant and raising the temperature of the water vapor by 300°CRkwl, calculate the amount of heat transfer from the water vapor to the water vapor.
The propane is contained in a piston-cylinder assembly, which maintains constant pressure at 0.2 MPa. If...
The propane is contained in a piston-cylinder assembly, which maintains constant pressure at 0.2 MPa. If a mixture with a quality of 0.65 and a total volume of 0.07 m3 is slowly heated to a temperature of 54°C, a) what was the total work into the system b) what was the total amount of heat added to the system. Please explain what tables you use to find the answer.
The propane is contained in a piston-cylinder assembly, which maintains constant pressure at 0.2 MPa. If...
The propane is contained in a piston-cylinder assembly, which maintains constant pressure at 0.2 MPa. If a mixture with a quality of 0.65 and a total volume of 0.07 m3 is slowly heated to a temperature of 54°C. a) what was the total work into the system. b) what was the total amount of heat added to the system.
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT