Question
In: Mechanical Engineering
A sheet of metal of 2 m ´ 2 m and 1.5 mm thickness is being tested in a wind tunnel.
A sheet of metal of 2 m ´ 2 m and 1.5 mm thickness is being tested in a wind tunnel.
a. Calculate the critical velocity, in m/s, at which the boundary layer will remain laminar.
b. For an upstream velocity of 35 m/s, what percentage of the metal sheet surface will have a laminar boundary layer.
c. For each of the previous cases (all laminar B.L and mixed laminar/turbulent B.L), calculate the drag force on the plate, in N. Use Table 9.3 to calculate the appropriate drag coefficients.
Solutions
samet mamat answered 2 years agoRelated Solutions
A wing-body model is tested in a wind tunnel with a flow of 100 m/s at...
A wing-body model is tested in a wind tunnel with a
flow of 100 m/s at standard sea-level conditions.
The wing area is 1.5 m^2 and the mean aerodynamic
chord length is 0.45 m. Measurements of lift force, L, and moment
about the center of gravity, MCG are made using the wind tunnel
force balance.
The lead mass is removed and a horizontal tail without
an elevator is added to the model. The distance from the airplane
center of gravity...
Air is flowing in a 1.5 m2 wind tunnel at 200 m/s at a pressure of...
Air is flowing in a 1.5 m2 wind tunnel at 200 m/s at
a pressure of 250kPa, and temperature of 20°C at the entrance.
Calculate:
(i) Mach number
(ii) Total Temperature
(iii) Total Pressure
(iv) Mass flow rate of air.
A new two-dimensional airfoil constant chord model is being tested in a wind tunnel. The model...
A new two-dimensional airfoil constant chord model is being
tested in a wind tunnel. The model chord is 3ft. The atmosphere is
standard. The velocity of the airflow is 250 ft/s. The forces are
resolved as 150lb of perpendicular to the relative wind and 10lb
parallel to the relative wind. Find the dynamic pressure and the
section coefficient of lift (cl) and the
section coefficient of drag (cd).
A sheet metal with a thickness of 3 mm has a limiting drawing ratio of 2.4....
A sheet metal with a thickness of 3 mm has a limiting drawing
ratio of 2.4. Calculate the largest circular blank that could be
used successfully in deep drawing a cylindrical cup with an
internal diameter of 75 mm. Also calculate the punch force required
when the sheet metal has an ultimate tensile strength of 530
MPa.
A P - 51 Musta ng (WWII plane) is tested in the large wind tunnel at...
A P - 51 Musta ng (WWII plane) is tested in the large wind
tunnel at NASA Ames. The plane has a pitot - static probe system
mounted. We want to test the P - 51 at a flight speed of 160 mph
and altitude of 40,000 ft. T he wind tunnel’s test section has a
cross - sectional area of 5000 ft 2 and a reservoir area of 100,000
ft 2 .
What pressure is needed in the reservoir...
Consider a sheet of paper with a thickness of 0.1 mm and a dielectric constant of...
Consider a sheet of paper with a thickness of 0.1 mm and
a dielectric constant of 3. Suppose we would like to make a 1 F
capacitor using this sheet as a spacer between two metallic
plates.
Suppose we took out the paper dielectric (while keeping
somehow the distance between the plates the same).
1.26: What is the charge after the paper sheet is out
completely?
1.27: What is voltage across the capacitor after the
paper sheet is out completely?...
The manufacturer of hardness testing equipment uses steel-ball indenters to penetrate metal that is being tested....
The manufacturer of hardness testing equipment uses steel-ball
indenters to penetrate metal that is being tested. However, the
manufacturer thinks it would be better to use a diamond indenter so
that all types of metal can be tested. Because of differences
between the two types of indenters, it is suspected that the two
methods will produce different hardness readings. The metal
specimens to be tested are large enough so that two indentions can
be made. Therefore, the manufacturer uses both...
The manufacturer of hardness testing equipment uses steel-ball indenters to penetrate metal that is being tested....
The manufacturer of
hardness testing equipment uses steel-ball indenters to penetrate
metal that is being tested. However, the manufacturer thinks it
would be better to use a diamond indenter so that all types of
metal can be tested. Because of differences between the two types
of indenters, it is suspected that the two methods will produce
different hardness readings. The metal specimens to be tested are
large enough so that two indentions can be made. Therefore, the
manufacturer uses both...
The manufacturer of hardness testing equipment uses steel-ball indenters to penetrate metal that is being tested....
The manufacturer of hardness testing equipment uses steel-ball
indenters to penetrate metal that is being tested. However, the
manufacturer thinks it would be better to use a diamond indenter so
that all types of metal can be tested. Because of differences
between the two types of indenters, it is suspected that the two
methods will produce different hardness readings. The metal
specimens to be tested are large enough so that two indentions can
be made. Therefore, the manufacturer uses both...
The manufacturer of hardness testing equipment uses steel-ball indenters to penetrate metal that is being tested....
The manufacturer of hardness testing equipment uses steel-ball
indenters to penetrate metal that is being tested. However, the
manufacturer thinks it would be better to use a diamond indenter so
that all types of metal can be tested. Because of differences
between the two types of indenters, it is suspected that the two
methods will produce different hardness readings. The metal
specimens to be tested are large enough so that two indentions can
be made. Therefore, the manufacturer uses both...
ADVERTISEMENT
ADVERTISEMENT
Latest Questions
- Suggest journal, research paper link reference. i need this as reference for writing a research with...
- Cryptography is used heavily in internet communications. True or false? Explain
- Suppose Rialto is the only movie cinema in a small college town, so it is essentially...
- With VMI, members of the supply chain share planning, demand, forecasting, and inventory information.
- Large lots are desirable in supply chain coordination despite increasing holding costs.
- ***Convert the C++ to Python*** #include <iostream> using std::cout; using std::cin; using std::endl; int charClass; char...
- Make-or-Buy Decision Fremont Computer Company has been purchasing carrying cases for its portable computers at a...
ADVERTISEMENT