Question

In: Mechanical Engineering

Write a program to run on your Arduino and PortMaster board that will sequentially turn on...

Write a program to run on your Arduino and PortMaster board that will sequentially turn on and off the LED segments, so it resembles Cylon eyes (https://youtu.be/UajcgzK2shQ). Use the millis() construct shown in lecture rather than delay(). The traverse from one side to the other should take about 1 second.

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

Write Arduino program to implement wiring three momentary switches to the Arduino board
Write Arduino program to implement wiring three momentary switches to the Arduino board
Write a program that captures the transmission of a character from an Arduino board over serial...
Write a program that captures the transmission of a character from an Arduino board over serial communication (UART)
WRITE CODE IN JAVA it is now your turn to create a program of your choosing....
WRITE CODE IN JAVA it is now your turn to create a program of your choosing. If you are not sure where to begin, think of a task that you repeat often in your major that would benefit from a program. For example, chemistry unit conversions, finding the area for geometric shapes, etc. You can also create an interactive story that changes based on the user input/decisions. The possibilities are endless. The program must include instructions for the user. Be...
Write the following in C language for Arduino: Write a program that turns on the LED...
Write the following in C language for Arduino: Write a program that turns on the LED at 25%, 50%, 75%, 100%, and then 0% brightness with a one second delay in between each change. Remember you are going to need to use a PWM pin and use the "analogWrite" command. The maximum value for our Arduino R3 boards is 255 and you need five steps (25%, 50%, 75%, 100%, and 0%) so you will need to determine the values for...
Write the following in C language for Arduino: Write a program that increases the LED brightness...
Write the following in C language for Arduino: Write a program that increases the LED brightness in five steps with each press of the button. Remember you are going to using a digital input and the "digitalRead" command. You are going to need to use a PWM pin and use the "analogWrite" command. The maximum value for our Arduino R3 boards is 255 and you need five steps (25%, 50%, 75%, 100%, and 0%) so you will need to determine...
Pharaphrase and rewrite the following paragraph: Arduino Arduino Uno is a microcontroller board b... pharaphrase and...
Pharaphrase and rewrite the following paragraph: Arduino Arduino Uno is a microcontroller board b... pharaphrase and rewrite the following paragraph: Arduino Arduino Uno is a microcontroller board based on the ATmega328P (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, an ICSP header and a reset button. It contains everything needed to support the microcontroller; simply connect it to...
Write a program in Arduino that, when it takes in a voltage range (0 to 5...
Write a program in Arduino that, when it takes in a voltage range (0 to 5 volts), gives a corresponding servo motor angle with a range from 0 to 180 degrees.
Produce program code to facilitate LED and switch interface with a microcontroller-based development board (Arduino). Explain...
Produce program code to facilitate LED and switch interface with a microcontroller-based development board (Arduino). Explain the programming process and interface circuits required
Write an Arduino Program that detects a reflective surface using the line sensor array of a...
Write an Arduino Program that detects a reflective surface using the line sensor array of a QTR-3RC (*Must be specific to this sensor! please this is important*) Must include a function that when called returns.. 0 (line to the left of the robot) 1 (line under the robot on the left side) 2 (line under the robot on the right side) 3 (line to the right of the robot) Output the results to the serial port in 0.5 second intervals...
Write an Arduino Program that detects a reflective surface using the line sensor array of a...
Write an Arduino Program that detects a reflective surface using the line sensor array of a QTR-3RC (*Must be specific to this sensor! please this is important*) Must include a function that when called returns.. 0 (line to the left of the robot) 1 (line under the robot on the left side) 2 (line under the robot on the right side) 3 (line to the right of the robot) Output the results to the serial port in 0.5 second intervals...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT