Question

In: Mechanical Engineering

A sensor outputs a voltage in the range of ±3mV. Your A/D samples at 1000 Hz,...

A sensor outputs a voltage in the range of ±3mV. Your A/D samples at 1000 Hz, has an input range of ±10V, and has a 12-bit resolution. Design an active filter to amplify the sensor signal to fit at least 75% of the range of the A/D and filter anything above the Nyquist frequency. Justify your assumptions and show your work.

Solutions

Expert Solution

samet mamat answered 2 years ago
Next > < Previous

Related Solutions

A sing-around sensor outputs frequency 40 Hz. Knowing that the average flow rate in the pipe...
A sing-around sensor outputs frequency 40 Hz. Knowing that the average flow rate in the pipe is Q= 40 l/min and the pipe radius is 2cm. What would be the distance between the emitting and receiving wires?
The voltage across an inductor is 65 V and has a frequency of 430 Hz. If...
The voltage across an inductor is 65 V and has a frequency of 430 Hz. If the current in the inductor is 0.27 A, what is the value of its inductance?
An ac generator with a frequency of 30.0 Hz and an rms voltage of 14.0 V...
An ac generator with a frequency of 30.0 Hz and an rms voltage of 14.0 V is connected to a 65.0 μF capacitor. 1. What is the maximum current in this circuit? 2. What is the current in the circuit when the voltage across the capacitor is 4.30 V and increasing? 3. What is the current in the circuit when the voltage across the capacitor is 4.30 V and decreasing?
An AC generator supplies an rms voltage of 230 V at 60.0 Hz. It is connected...
An AC generator supplies an rms voltage of 230 V at 60.0 Hz. It is connected in series with a 0.300 H inductor, a 4.30 μF capacitor and a 256 Ω resistor. What is the impedance of the circuit? What is the rms current through the resistor? What is the average power dissipated in the circuit? What is the peak current through the resistor? What is the peak voltage across the inductor? What is the peak voltage across the capacitor?...
An AC generator supplies an rms voltage of 230 V at 60.0 Hz. It is connected...
An AC generator supplies an rms voltage of 230 V at 60.0 Hz. It is connected in series with a 0.400 H inductor, a 3.40 μF capacitor and a 206 Ω resistor. What is the impedance of the circuit? Tries 0/20 What is the rms current through the resistor? Tries 0/20 What is the average power dissipated in the circuit? Tries 0/20 What is the peak current through the resistor? Tries 0/20 What is the peak voltage across the inductor?...
A 120 V rms voltage at 60.0 Hz is applied across an inductor, a capacitor, and...
A 120 V rms voltage at 60.0 Hz is applied across an inductor, a capacitor, and a resistor in series. If the peak current in this circuit is 0.84840 A, what is the impedance of this circuit?
A series ac circuit consists of a voltage source of frequency f = 60 Hz and...
A series ac circuit consists of a voltage source of frequency f = 60 Hz and source voltage amplitude 345 volts, a resistor of resistance R = 255 Ω, a capacitor of capacitance C = 6.2×10−6F, and an inductor of inductance L. (a) What must be the value of L for the phase angle Φ to be zero? (b) When L has the value calculated in (a), what is the current amplitude in the circuit?
A 100 Hz AC voltage source, with a peak output of 170 V, is connected to...
A 100 Hz AC voltage source, with a peak output of 170 V, is connected to an inductor. If the rms current through the inductor is 1 A, what is the value of the inductor? 1. 1.9 H 2. 190 mH 3. 19 mH 4. 1.9 mH
An AC generator supplies an rms voltage of 240 V at 50.0 Hz. It is connected...
An AC generator supplies an rms voltage of 240 V at 50.0 Hz. It is connected in series with a 0.350 H inductor, a 3.60 μF capacitor and a 211 Ω resistor. 1. What is the impedance of the circuit? 2. What is the rms current through the resistor? 3. What is the average power dissipated in the circuit? 4. What is the peak current through the resistor? 5. What is the peak voltage across the inductor? 6. What is...
The specification of a pressure sensor is shown below: Range of measurement: 10 psi to 250...
The specification of a pressure sensor is shown below: Range of measurement: 10 psi to 250 psi. Accuracy : ±0.2% of span. Transfer function : 0.5?/psi. Transfer function accuracy: ±0.1% Sensor output resistance, R : 2k? - 20k?. Sensor time constant: 200 ms . The resistance is then converted to a voltage with the transfer function: V= 10R/R+1000 1/Determine the uncertainty for measurement of 120psi. What is the possible pressure? 2/Determine the possible range of the transfer function. Interpret the...
ADVERTISEMENT
Subjects
ADVERTISEMENT
Latest Questions
ADVERTISEMENT